781923
27
Zoom out
Zoom in
Previous page
1/112
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 27
The number of passes required to reach a desired
-
ture content of soil. Maximum soil compaction has
been reached when excessive kickback is noticed.



and a possible obstacle. Special care is required
when working on uneven ground or when compact-

operating the machine under such conditions. In
operation, guide the machine, but let the compactor
do the work. Bearing down on the handle is unnec-


On uneven surfaces or inclines, light forward

compactor in moving forward.

the bottom of the plate to prevent chipping or grind-
ing surface of the stones.
-

to stick together and prevent good compaction. If

compacting.
-
ating plate, some moisture should be added to the
ground material to improve compacting. This will

The following points are to be observed when com-

1. -


2. The operator must never stand in the direction of
descent.
3. The max. gradient of 20° must not be exceeded
m If this gradient were exceeded, this would
result in a failure of the engine lubrication
system (splash lubrication and thus inevita-
bly lead to a breakdown of important engine
components.
Stopping engine


conditions, use the following procedure.
1. To stop the compactor from traveling, return the

langsam schnell
vitesse lente vitesse rapide
slow fast
Pomalu rychle
Pomalý rýchly
Počasnega hitrega
lassú gyors
бавно бързо
Nopea hidas
.
2. Allow engine to cool down for one or two minutes
before stopping.
Checking the engine oil (g. E)


without screwing down.
If the oil is too low, add the recommenced oil in.
   -

Check fuel
First stop the engine, open the fuel cover, and check
oil level. If the oil level is too low, add the fuel to full,

the fuel over the shoulder of the carburettor when

-
line For unleaded gasoline, can make carbon deposit

Don’t use used and contaminated or gasoline with
oil. Avoid the dirt and water entering into fuel tank.
Starting engine (g. I)
      

CLOSE position .
To restart a warm engine, leave the choke lever
 .
-




Recoil starter (17)
-



move it to the OPEN position as the engine warms


at the desired position. Plate will begin vibrating and
proceed with compacting.
Forward and reverse motion (g. F)
The direction of travel is determined with the oper-

of the control shifter, the plate compacts in forward
direction or in reverse direction.
1. To make the compactor move in the forward direc-

2. To make the compactor move in the reverse direc-

m Do not operate plate on concrete or on
extremely hard, dry, compacted surfaces. The
plate will jump rather than vibrate and could
damage both plate and engine.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HP2500S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HP2500S in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 7.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info