781866
32
Zoom out
Zoom in
Previous page
1/148
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58 www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
32 | GB
16. Trouble shooting
The following table shows fault symptoms and describes remedial measures in the event of your machine failing to work
properly. If you cannot localise and rectify the problem with this, please contact your service workshop.
Fault Possible cause Remedy
Engine fails to start.
Spark plug wire disconnected. Attach spark plug wire securely to spark plug.
Out of fuel or stale fuel. Fill with clean, fresh gasoline.
Throttle control lever not in correct
starting position. Move throttle control lever to start position.
Choke not in ON Position. Throttle must be positioned at choke for a cold
start.
Blocked fuel line. Clean the fuel line.
Fouled spark plug. Clean, adjust gap, or replace.
Engine ooding. Wait a few minutes to restart, but do not prime.
Engine runs erratically.
Spark plug wire loose. Connect and tighten spark plug wire.
Unit running on CHOKE. Move choke lever to OFF.
Blocked fuel line or stale fuel. Clean fuel line. Fill tank with clean, fresh gas-
oline.
Vent plugged. Clear vent.
Water or dirt in fuel system. Drain fuel tank. Rell with fresh fuel.
Dirty air cleaner. Clean or replace air cleaner.
Engine overheats. Dirty air cleaner. Clean air cleaner.
Air ow restricted. Remove housing and clean.
Engine will not stop when
throttle control is positioned
at stop, or engine speed does
not increase properly when
throttle control is adjusted.
Debris interfering with throttle link-
age. Clean dirt and debris.
Pull cord damaged Contact specialist dealer
Compactor is difcult to con-
trol when pounding (machine
jumps or lurches forward)
Too high engine speed on hard
ground.
Set the throttle lever at lower speed.
Shock absorber too loose or dam-
aged. Contact specialist dealer
No compacting function or
the plate compactor does not
reach the maximum speed
Damage on exciter or plate compac-
tor. Contact specialist dealer
Drive belt too loose and slips on the
pulley. Adjust or replace the drive belt
Oil loss from engine or exciter Worn seal. Contact specialist dealer
Leaks on housing.
IM_5904612903_HP2200s_191212_new.indd 32IM_5904612903_HP2200s_191212_new.indd 32 12.12.2019 07:40:2112.12.2019 07:40:21
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HP2200S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HP2200S in the language / languages: English, German, French, Italian, Polish as an attachment in your email.

The manual is 12.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info