Manual Scheppach HM90LXU (page 25 of 80) (English, German, French, Italian, Portuguese, Spanish)

782505

Zoom out

Zoom in

1/80

25GB

9.3 Cross cut 90° and turntable 0° (Fig.7/8)

In the case of cutting widths up to approx. 100 mm it

is possible to x the traction function of the saw with

the set screw (21) in the rear position. In this position

the machine can be operated in cross cutting mode.

If the cutting width is over 100 mm then it is necessa-

ry to ensure that the set screw (21) is loose and the

machine head (4) can move.

• Move the machine head (4) to its upper position.

• Use the handle (3) to push back the machine head

(4) and x it in this position if required (dependent

on the cutting width).

• Place the piece of wood to be cut at the stop rail

(17) and on the turntable (15).

• Lock the material with the clamping device (7) on

the xed saw table (16) to prevent the material from

moving during the cutting operation.

• Push down the release lever (2) to release the ma-

chine head (4).

• Press the ON/OFF switch (3) to start the motor.

• With the drag guide (22) xed in place:

use the handle (1) to move the machine head (4)

steadily and with light pressure downwards until

the saw blade (6) has completely cut through the

work piece.

• With the drag guide (22) not xed in place:

pull the machine head (4) all the way to the front.

Lower the handle (1) to the very bottom by applying

steady and light downward pressure. Now push the

machine head (4) slowly and steadily to the very

back until the saw blade (6) has completely cut

through the work piece.

• When the cutting operation is completed, mo-

ve the machine head back to its upper (home)

position and release the ON/OFF button (3).

Attention! The machine executes an upward stro-

ke automatically due to the return spring, i.e. do

not release the handle (1) after completing the cut;

instead allow the machine head to move upwards

slowly whilst applying light counter pressure.

9.4 Cross cut 90° and turntable 0° - 45° (Fig. 7/8)

The crosscut saw can be used to make crosscuts of

0° -45° to the left and 0° -45° to the right in relation to

the stop rail.

• Loosen set screw (11).

• Detent lever (12) pull with the index nger upward.

• Use the handle (11) to adjust the rotary table (15)

to the desired angle. The pointer (13) on the rotary

table must match the desired angle on the scale

(14) on the xed saw table (16).

• Re-tighten the set screw (11) in order to secure the

rotary table (15).

• Cut as described under section 9.3.

9.5 Precision adjustment of the stop for mitre cut

45° (Fig. 1/9/10)

• No stop angle included.

• Lower the machine head (4) and secure using the

locking bolt (24).

• Fix the rotary table (15) in the 0° position.

• Loosen the set screw (23) and use the handle (1)

to angle the machine head (4) 45° to the left.

• 45° - position angle stop (b) between the saw blade

(6) and rotary table (15).

• Adjust the adjusting screw (28) until the angle bet-

ween the saw blade (6) and rotary table (15) is

precisely 45°.

• It is not necessary to x this setting because it is

maintained by the spring pretension.

• Subsequently check the position of the angle in-

dicator. If necessary loosen the pointer (20) using

a Philips screwdriver, set to position 45° on the

angle scale (19) and re-tighten the retaining screw.

9.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/11)

The crosscut saw can be used to make mitre cuts of

0° - 45° in relation to the work face.

• Move the machine head (4) to the top position.

• Fix the rotary table (15) in the 0° position.

• Loosen the set screw (23 and use the handle (1)

to angle the machine head (4) to the left, until the

pointer (20) indicates the desired angle measure-

ment on the scale (19).

• Re-tighten the xing screw (23).

• Cut as described in section 9.3.

9.7 Mitre cut 0°- 45° and turntable 0°- 45°

(Fig. 2/4/12)

The crosscut saw can be used to make mitre cuts to

the left of 0°- 45° in relation to the work face and, at

the same time, 0° - 45° to the left or 0° - 45° to the

right in relation to the stop rail (double mitre cut).

• Move the machine head (4) to its upper position.

• Release the rotary table (15) by loosening the set

screw (11).

• Using the handle (1), set the rotary table (15) to the

desired angle (refer also to point 9.4 in this regard).

• Re-tighten the set screw (11) in order to secure

the rotary table.

• Undo the locking screw (23).

• Use the handle (1) to tilt the machine head (4) to

the left until it coincides with the required angle va-

lue (in this connection see also section 9.6).

• Re-tighten the xing screw (23).

• Cut as described under section 9.3.

9.8 Limiting the cutting depth (Fig. 3/13)

• The cutting depth can be innitely adjusted using

the screw (25). To do this loosen the knurled nut

(d) on the screw (25). Move the stop for the cutting

depth limitre (26) to the outside. Turn the screw

(25) in or out to set the required cutting depth.

Then re-tighten the knurled nut on the screw (25).

• Check the setting by completing a test cut.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HM90LXU in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5.85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HM90LXU Manual

Product: