781430
31
Zoom out
Zoom in
Previous page
1/168
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 31
        
screw (29) in the clockwise direction.


󰀨
out downwards.


Fit and fasten the new saw blade (6) in reverse or-
der.
Important! The cutting angle of the teeth, in other
words the direction of rotation of the saw blade (6)
must coincide with the direction of the arrow on the
housing.
Before continuing your work make sure that all safe-
ty devices are in good working condition.
Important! Every time that you change the saw
blade (6), check to see that it spins freely in the ta-
ble insert (10) in both perpendicular and 45° angle
settings.
Important! The work to change and align the saw
blade (6) must be carried out correctly.
8.11 Using the laser (g. 18)
Press the ON/OFF switch laser (33) 1x. A laser line is
projected onto the material you wish to process, pro-
viding an exact guide for the cut. Press again the ON/
OFF switch (34) to toggle between the laser (32) and
the LED working light (33):
ON/OFF switch laser/LED (34)
Press 1x. Laser ON / LED OFF
Press 2x. Laser OFF / LED ON
Press 3x. Laser ON / LED ON
Press 4x. Laser OFF / LED OFF
8.12 Adjusting the laser (g. 19-20)
If the laser (32) ceases to indicate the correct cutting
line, you can readjust the laser. To do so, open the
screws (32b) and remove the front cover (32a). Loos-
en the Philips head screws (E) and set the laser by
moving sideways until the laser beam strikes the teeth
of the saw blade (6).
After adjusting and tightening the laser, mount the
front cover by tightening both screws (32b) by hand.
9. Transport
Tighten the handle (11) to lock the rotary table.
Press the machine head (4) downwards and secure
with the locking bolt (23).
Fix the saw’s drag function with the locking screw
for drag guide (20) in rear position.

When reassembling the equipment proceed as de-
scribed under section 7.
Release the rotary table (14) by loosening the han-
dle (11).
Using the handle (11), set the rotary table (14) to the
desired angle (refer also to point 8.4 in this regard).
Re-tighten the handle (11) to secure the rotary table
(14).
Undo the set screw (22).
Use the handle (1) to tilt the machine head (4) to the
left until it coincides with the required angle value (in
this connection see also section 8.6).
Re-tighten the set screw (22).
Cut as described under section 8.3.
8.8 Limiting the cutting depth (g. 3/13)
       
the screw (24). To do this loosen the knurled nut
(24a) on the screw (24). Turn the screw (24) in or
out to set the required cutting depth. Then re-tighten
the knurled nut (24a) on the screw (24).
Check the setting by completing a test cut.
8.9 Sawdust bag (g. 1/22)
The saw is equipped with a debris bag (17) for sawdust
and chips.
Squeeze together the metal ring on the dust bag and
attach it to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a
zipper at the bottom.
Connection to an external dust extractor
Connect the vacuum hose with the dust extraction
spout.
The industrial vacuum cleaner must be suitable for
the material being worked.
When vacuuming dust that is especially detrimen-
tal to health or carcinogenic, use a special vacuum
cleaner.
8.10 Changing the saw blade (g. 1/2/14-17)
Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.
Risk of injury!
Swing the machine head (4) upwards and lock with
the locking bolt (23).
Loosen the retaining screw (5a) of the cover using a
Philips screwdriver.
WARNING! Do not fully remove this screw.
Fold the saw blade guard (5) upwards until the saw


screw (29).
Hold the Allen key (C) and slowly close the saw
blade guard (5) until it touches the Allen key (C).
Firmly press the saw shaft lock (30) and slowly ro-
       
The saw shaft lock (30) engages after no more than
one rotation.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HM216 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HM216 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 10.08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info