Manual Scheppach HM216 (page 28 of 168) (English, German, Dutch, French, Italian)

781430

Zoom out

Zoom in

1/168

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

28 | GB

Noise

Total noise values determined in accordance with EN

62841.

Sound pressure level LpA ........................... 96,5 dB(A)

Uncertainty KpA .................................................... 3 dB

Sound power level LWA ............................. 109,5 dB(A)

Uncertainty KWA .................................................... 3 dB

Wear hearing protection.

󰀨

The above-mentioned noise emission values were

measured in accordance with a standardised test pro-

cedure and can be used to compare one power tool

with another.

The above-mentioned noise emission values can also

be used for the preliminary assessment of exposure.

Warning:

• The noise emissions during the actual use of the

   󰀨   

values depending on the power tool being used, in

particular on the type of workpiece being processed.

• Try to keep emissions as low as possible, for ex-

ample by limiting your working time. In this regard,

all the operational cycle phases must be taken into

consideration (such as the times when the tool is

󰀨

7. Before starting the equipment

• Open the packaging and remove the device care-

fully.

• Remove the packaging material as well as the

packaging and transport bracing (if available).

• Check that the delivery is complete.

• Check the device and accessory parts for trans-

port damage.

• If possible, store the packaging until the warranty

period has expired.

ATTENTION

The device and packaging materials are not toys!

Children must not be allowed to play with plastic

bags, lm and small parts! There is a risk of swal-

lowing and su󰀨ocation!

• The equipment must be set up where it can stand

securely. Secure the machine on a workbench or a

base frame with 4 screws (not included in delivery)



• Pull out the pre-installed tilt protection (37) com-

pletely and secure it with an Allen key (D).

• All covers and safety devices have to be properly



• It must be possible for the blade to run freely.

• Furthermore, despite all precautions having been

met, some non-obvious residual risks may still re-

main.

• Residual risks can be minimised if the „safety in-

structions“ and the „Proper use“ are observed along

with the whole of the operating instructions.

• Do not load the machine unnecessarily: excessive

pressure when sawing will quickly damage the saw

blade, which results in reduced output of the ma-

chine in the processing and in cut precision.

• When cutting plastic material, please always use

clamps: the parts which should be cut must always



• Avoid accidental starting of the machine: the operat-

ing button may not be pressed when inserting the

plug in an outlet.

• Use the tool that is recommended in this manual.

In doing so, your machine provides optimal perfor-

mance.

• Hands may never enter the processing zone when

the machine is in operation.

• 󰀨-

chine prior to any operations.

6. Technical data

AC motor ...................................... 220 - 240 V~ 50Hz

Power S1 .................................................... 1700 Watt

Operating mode ................................ S6 25%* 2000W

Idle speed n0 ............................................... 4700 min-1

Carbide saw blade ...................ø 216 x ø 30 x 2,8 mm

Number of teeth .......................................................24

Maximum tooth width of saw blade ....................3 mm

Swivel range ........................................ -45° / 0°/ +45°

Mitre cut ...................................... 0° bis 45° to the left

Saw width at 90° ..................................... 340 x 65 mm

Saw width at 45° ..................................... 240 x 65 mm

Saw width at 2 x 45°

(double mitre cut)....................................240 x 38 mm

Protection class ...................................................II /

Weight .......................................................ca. 12,0 kg

Laser class ................................................................2

Wavelength of laser .........................................650 nm

Laser output....................................................< 1 mW

* S6, continuous operation periodic duty.

Identical duty cycles with a period at load followed by

a period at no load. Running time 10 minutes; duty

cycle is 25% of the running time.

The work piece must have a minimum height of 3

mm and a minimum width of 10 mm.

Make sure that the workpiece is always secured

with the clamping device.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HM216 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 10.08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HM216 Manual

Product: