759296
27
Zoom out
Zoom in
Previous page
1/236
Next page
27GB
(33) and inner ange (39).
Insert the new saw blade (7) in the reverse se-
quence and tighten.
Position the guide bar (40) on the pin again, and se-
cure with the spring (41).
Important! The cutting angle of the teeth, in other
words the direction of rotation of the saw blade (7)
must coincide with the direction of the arrow on the
housing.
Before continuing your work make sure that all safe-
ty devices are in good working condition.
Important! Every time that you change the saw
blade (7), check to see that it spins freely in the ta-
ble insert (11) in both perpendicular and 45° angle
settings.
Important! The work to change and align the saw
blade (7) must be carried out correctly.
8.11 Using the laser (Fig. 16,17)
To switch on: Move the ON/OFF switch of the laser
(35) to the “1” position. A laser line is projected onto
the material you wish to process, providing an exact
guide for the cut.
To switch off: Move the ON/OFF switch of the laser
(35) to the “0” position.
Replacing the battery: Switch off the laser (34).
Remove the battery compartment cover (37). Re-
move the batteries and replace with new batter-
ies (3 x AG13) Check that the battery terminals are
positioned correctly when inserting new batteries.
Close the battery compartment (36) again.
8.12 Changing the speed (Fig. 2)
The saw has 2 speed ranges:
langsam schnell
vitesse lente vitesse rapide
slow fast
Pomalu rychle
Pomalý rýchly
Počasnega hitrega
lassú gyors
бавно бързо
Nopea hidas
To operate the saw at a speed of 3200 rpm (metal),
set the switch (42) to position I.
To operate the saw at a speed of 4500 rpm (wood),
set the switch (42) to position II.
9. Transport (Fig. 1,2)
Tighten the set screw (26) in order to lock the rotary
table (16)
Activate the release lever (3), press the machine
head (5) downwards and secure with the safety pin
(24). The saw is now locked in its bottom position.
Fix the saw’s drag function with the locking screw for
drag guide (23) in rear position.
Carry the equipment by the xed saw table (17).
When reassembling the equipment proceed as de-
scribed under section 7.1.
10. Maintenance
m Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time
using a cloth. In order to extend the service life of the
tool, oil the rotary parts once monthly. Do not oil the
motor.
When cleaning the plastic do not use corrosive prod-
ucts.
Brush inspection
Check the carbon brushes after the rst 50 operating
hours with a new machine, or when new brushes have
been tted. After carrying out the rst check, repeat the
check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the spring
or contact wire are burned or damaged, it is necessary
to replace both brushes. If the brushes are found to be
usable following removal, it is possible to reinstall them.
11. Storage
Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.
12. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions.
The customer‘s mains connection as well as the
extension cable used must also comply with these
regulations.
Important information
In the event of an overloading the motor will switch
itself off. After a cool-down period (time varies) the mo-
tor can be switched back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
Passage points, where connection cables are
passed through windows or doors.
Kinks where the connection cable has been improp-
erly fastened or routed.
Places where the connection cables have been cut
due to being driven over.
Insulation damage due to being ripped out of the
wall outlet.
Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the ap-
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HM100MP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HM100MP in the language / languages: English, German, Danish, French, Italian, Polish, Spanish, Finnish as an attachment in your email.

The manual is 9,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info