781961
26
Zoom out
Zoom in
Previous page
1/152
Next page
26
Störung Mögliche Ursache Abhilfe
1. Motor beendet selbständig
Spaltvorgang
Überspannungs-Schutzvorrichtung
wurde ausgelöst
Elektrofachkraft anrufen
2. Spaltgut wird nicht gespaltet a) Maschine falsch bestückt
b) Spaltgut-Umfang übersteigt
Motorkapazität
c) Spaltkeil ist stumpf
d) Öl tritt aus
a) Spaltgut richtig einlegen, siehe
auch „Bedienung”
b) Spaltgut in passendere Größe
sägen
c) Spaltkeil schleifen
d) Undichte Stelle lokalisieren,
Händler anrufen
3. Druckplatte vibriert, erzeugt
Geräusche
Ölmangel und Luftüberschuss
im hydr. System
Ölstand prüfen, ggf. Öl nachfüllen,
ansonsten Händler anrufen
4. Ölaustritt am Zylinder oder an
anderen Stellen
a) Lufteinschluss im hydr.
System während Betrieb
b) Entlüfterschraube vor
Transport nicht angezogen
c) Öl-Abuss-Schraube locker
d) Ölventil und/oder Dichtungen
defekt
a) Entlüfterschraube vor Gebrauch
einige Umdrehungen lösen
b) Entlüfterschraube vor Transport
fest anziehen
c) Öl-Abuss-Schraube fest anziehen
d) Händler anrufen
Problem Possible Cause Remedy
1. Motor stops starting Overload protection device
disengaged to protect the log splitter
from being damaged
Contact a qualied Electrician.
2. Fails to split logs a) Log is improperly positioned
b) Size of log exceeds the capacity of
the machine
c) Wedge cutting edge is blunt
d) Oil leaks
a) Refer to ”operation” section to
perfect log loading
b) Reduce log size before operating
c) Sharpen cutting edge
d) Locate leak(s) and contact your
dealer
3. Log pusher moves jerkily, taking
unfamiliar noise or vobrating a lot
Lack of hydraulic oil and excessive air
in the hydraulic system
Check oil level for possible relling.
Contact your dealer
4. Oil leaks around the cylinder ram
or 󰀨rom other points
a) Air sealed in hydraulic system while
operating
b) Bleed screw is not tightened before
moving the log splitter
c) Oil drain bolt is not tight
d) Hydraulic control valve assembly
and/or seal(s) worn
a) Loosen bleed screw by some
rotations before operating the log
splitter
b) Tighten bleed screw up before
moving the log splitter
c) Tighten the oil drain bolt
d) Contact your dealer
Problème Possible cause Réparature
1. Le moteur achève lui-même la
produre de fente
Le dispositif limiteur de tension a été
déclenché
Appeler un électricien
2. Le morceau de bois à fendre n’a
pas été fendu
a) Machine mal outillée
b) La taille de la pièce à usiner
dépasse la capacité du moteur
c) Le départoir est émous
d) De l’huile s’échappe
a) Bien positionner la pièce à usiner,
voir également ’Maniement
b) Scier la pièce à usiner à une taille
plus appropriée
c) Rectier le départoir
d) Localiser lendroit non étanche,
appeler le commerçant
3. La plaque de serrage vibre, fait du
bruit
Manque d’huile et trop dair
dans le système hydr.
Contrôler le niveau d’huile, le cas
échéant rajouter de l’huile, et sinon
appeler le commerçant
4. Fuite d’huile sur le vérin ou à
d’autres endroits
a) Inclusion dair dans le
système hydr. durant le
fonctionnement
b) Vis daération pas serrée
avant le transport
c) Vis de vidange d’huile lâche
d) Soupape d’huile et/ou joints
défectueux
a) Desserrer la vis d’aération avant
l’utilisation en la tournant quelques
fois
b) Serrer la vis daération avant le
transport
c) Serrer la vis de vidange
d) Appeler le commerçant
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HL650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HL650 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 5.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info