781961

Scheppach HL650 Manual

19
Zoom out
Zoom in
Previous page
1/152
Next page
19
1. Release both controls.
2. After the log pusher moves back and completely stops
at its starting position, insert a wedge wood under the
jammed log as shown in the gure.
3. Start the log splitter to push the wedge wood under
the jammed one.
4. Repeat above procedure with sharper slope wedge
woods until the log is completely freed.
Oil Change
The hydraulic system is a closed system with oil tank, oil
pump and control valve.
Check hydraulic connections and ttings regularely for
air tightness. Tighten when necessary.
The oil tank has been lled with high quality oil at the
factory.
Replacing hydraulic oil after 150 hours of use
(Fig. 5,6)
1. Make sure all moving parts stop and the log splitter is
unplugged.
2. Unscrew oil drain screw (11) to remove it.
3. Turn the log splitter on the support leg side as shown
in g. 5 over a 4 liter capacity container to drain the
hydraulic oil o󰀨. Recycle carefully!
4. Turn your scheppach machine on the motor side as
shown in Fig. 6 to rell about 3,5 l fresh oil.
5. Clean the surface of the dip stick on the oil drain bolt
and put it back into the oil tank while keeping the log
splitter vertically. Make sure the level of the relled oil
is just between 2 grooves around the dip stick.
6. Clean the oil drain bolt before threading it back. Make
sure it is tightened to avoid leakage before placing the
log splitter horizontally. Afterwards start splitting with-
out actually splitting log several times.
Periodically check oil level. Upon low oil level oil relling
is required.
Dispose of the used oil in a correct manner at a
public collection facility. It is prohibited to drop old
oil on the ground or to mix it with waste.
We recommend the following hydraulic oils:
Aral Vitam gf 22
BP Energol HLP-HM 22
Mobil DTE 11
Shell Tellus 22
or oils of same quality.
Do not use any other types of oil as they would inu-
ence the function of the hydraulic cylinder.
1. Reculer la plaque de serrage jusqu’en position initiale.
2. Placer un coin sous le morceau de bois à fendre,
comme indiqué dans la gure.
3. Déclencher une procédure de fente de sorte que la
plaque de serrage pousse le coin bien loin au-dessus
du morceau de bois à fendre devant être dégagé.
4. Répéter les étapes précédentes avec de nouveaux
coins de façon à pouvoir extraire le morceau de bois
à fendre de la machine en le poussant vers le haut.
Hydraulique/vidange d’huile
L’installation hydraulique est un système fermé avec
réservoir d’huile, pompe à huile et valve de commande.
Il est interdit de le modier ou manier.
Contrôler régulièrement si les raccordements et les rac-
cords à vis sont étanches, le cas échéant, les resserrer.
Au départ de nos usines, le réservoir d’huile est rempli
d’huile hydraulique de haute qualité à degré
E󰀨ectuer une vidange d’huile après toutes les 150
heures de service (Fig. 5,6)
1. La plaque de serrage est en position initiale. Décon-
necter la machine du branchement secteur.
2. Desserrer la vis de vidange d’huile (11) et la poser de
côté.
3. Poser une cuve 4-1 vide à côté de votre machine
scheppach et la redresser, comme montré dans la g.
5. Attendre jusqu’à ce que toute l’huile ancienne soit
écoulée. Elimination conforme à l’environnement!
4. Renverser maintenant la machine scheppach (Fig. 6)
an de rajouter env. 3,5 l d’huile hydraulique.
5. Une jauge d’huile est intégrée dans la vis de vidange
d’huile. Essuyer cette jauge et l’introduire dans la ma-
chine encore en position verticale. En la ressortant,
un lm d’huile doit alors être visible entre les deux rai-
nures.
6. Resserrer à fond ensuite la vis de vidange d’huile. Ac-
tionner ensuite plusieurs fois la machine HL650 sans
morceau de bois.
Le niveau d’huile doit être contrôlé régulièrement et le
cas échéant, il faut rajouter de l’huile.
Eliminez l’huile usagée de manière réglementaire à
l’endroit prévu à cet e󰀨et. Il est interdit de déverser
de l’huile usagée dans le solo u de la mélanger à
des déchets.
Nous conseillons les huiles hydrauliques sui-
vantes:
Aral Vitam gf 22, BP Energol HLP-HM 22
Mobil DTE 11, Shell Tellus 22
ou équivalent.
Eviter d’utiliser d’autres huiles! Utiliser d’autres
huiles a des répercussions sur le fonctionnement du
cylindre hydraulique.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HL650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HL650 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 5.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info