Manual Scheppach HL450 (page 22 of 88) (All languages)

644531

Zoom out

Zoom in

1/88

Störung Mögliche Ursache Abhilfe

1. Motor beendet selbständig

Spaltvorgang

ÜberspannungsSchutzvorrichtung

wurde ausgelöst

Elektrofachkraft anrufen

2. Spaltgut wird nicht gespaltet a) Maschine falsch bestückt

b) Spaltgut-Umfang übersteigt

Motorkapazität

c) Spaltkeil ist stumpf

d) Öl tritt aus

a) Spaltgut richtig einlegen, siehe auch

„Bedienung”

b) Spaltgut in passendere Größe sägen

c) Spaltkeil schleifen

d) Undichte Stelle lokalisieren, Händler

anrufen

3. Druckplatte vibriert, erzeugt

Geräusche

Ölmangel und Luftüberschuss

im hydr. System

Ölstand prüfen, ggf. Öl nachfüllen,

ansonsten Händler anrufen

4. Ölaustritt am Zylinder oder an

anderen Stellen

a) Lufteinschluss im hydr.

SystemwährendBetrieb

b) Entlüfterschraube vor

Transport nicht angezogen

c) Öl-Abﬂuss-Schraube locker

d) Ölventil und/oder Dichtungen defekt

a) Entlüfterschraube vor Gebrauch

einige Umdrehungen lösen

b) Entlüfterschraube vor Transport fest

anziehen

c) Öl-Abﬂuss-Schraube fest anziehen

d) Händler anrufen

Problem Possible Cause Remedy

1. Motor stops starting Overload protection device disengaged

to protect the log splitter from being

damaged

Contact a qualiﬁed Electrician.

2. Fails to split logs a) Log is improperly positioned

b) Size of log exceeds the capacity of

the machine

c) Wedge cutting edge is blunt

d) Oil leaks

a)Referto”operation”sectionto

perfect log loading

b) Reduce log size before operating

c) Sharpen cutting edge

d) Locate leak(s) and contact your

dealer

3. Log pusher moves jerkily, taking

unfamiliar noise or vobrating a lot

Lack of hydraulic oil and excessive air

in the hydraulic system

Check oil level for possible reﬁlling.

Contact your dealer

4. Oil leaks around the cylinder ram or

ffrom other points

a) Air sealed in hydraulic system while

operating

b)Bleedscrewisnottightenedbefore

moving the log splitter

c) Oil drain bolt is not tight

d) Hydraulic control valve assembly

and/or seal(s) worn

a) Loosen bleed screw by some

rotations before operating the log

splitter

b) Tighten bleed screw up before

moving the log splitter

c) Tighten the oil drain bolt

d) Contact your dealer

Problème Possible cause Réparature

1. Le moteur achève lui-même la

procédure de fente

Le dispositif limiteur de tension a été

déclenché

Appeler un électricien

2. Le morceau de bois à fendre n’a pas

été fendu

a) Machine mal outillée

b) La taille de la pièce à usiner

dépasse la capacité du moteur

c) Le départoir est émoussé

d) De l’huile s’échappe

a)Bienpositionnerlapièceàusiner,

voir également ’Maniement’

b) Scier la pièce à usiner à une taille

plus appropriée

c) Rectiﬁer le départoir

d) Localiser l’endroit non étanche,

appeler le commerçant

3. La plaque de serrage vibre, fait du

bruit

Manque d’huile et trop d’air

dans le système hydr.

Contrôlerleniveaud’huile,lecas

échéant rajouter de l’huile, et sinon

appeler le commerçant

4. Fuite d’huile sur le vérin ou à

d’autres endroits

a) Inclusion d’air dans le

système hydr. durant le

fonctionnement

b) Vis d’aération pas serrée

avant le transport

c) Vis de vidange d’huile lâche

d) Soupape d’huile et/ou joints

défectueux

a) Desserrer la vis d’aération avant

l’utilisation en la tournant quelques

fois

b) Serrer la vis d’aération avant le

transport

c) Serrer la vis de vidange

d) Appeler le commerçant

Downloaded from www.Manualslib.com manuals search engine

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HL450 in the language / languages: All languages as an attachment in your email.

The manual is 3,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HL450 Manual

Product: