Manual Scheppach HL3000GM (page 26 of 120) (English, German, French, Italian)

781854

Zoom out

Zoom in

1/120

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

26 | GB

Using the safety arm (Fig. 15)

The safety arm can be set at different height posi-

tions, depending on the length of the wood.

Splitting (Fig. 16 + 17)

• If the outside temperature is below 5°C, let the ma-

chine run idle for about 5 minutes so the hydraulic

system reaches its operating temperature. Place

the log under the splitting blade vertically.

Caution: The splitting blade is very sharp. Risk

of injury!

• When you push both operating levers down, the

splitting blade goes down and splits the wood.

• Only ever split logs that have been sawn off straight.

• Split the log vertically.

• Never split it lying down or diagonally to the grain!

• Wear suitable gloves and safety boots when split-

ting wood.

• Split very misshapen logs from the edge.

Caution: During splitting, some logs can be un-

der signicant tension and suddenly break.

• Force jammed logs out by applying pressure in

the splitting direction or by raising the riving

knife. In this case, only push the handles up,

do not use the return bracket. Caution: Risk of

injury

Operating the log lifter (6)

General information about the log lifter:

• For safety reasons, the log lifter chain may only be

hung on the splitting blade with the last link.

• Ensure that nobody else is within the working envi-

ronment of the log lifter.

Operating the log lifter:

• Loosen the log lifter restraining hook so the lifting

tube can move freely.

• Move the splitting blade so far down that the log

lifter lifting tube lies on the ground.

• In this position, you can roll the log to be split onto

the lifting tube. (The log has to be between the two

xing tips.)

• Push the return bracket down or the handles up

so the splitting blade moves up. (Caution! Do not

stand in the working environment of the log lifter!

Risk of injury!)

• Now align the log, push it against the retention

thorn and split it (see: Operating instructions).

• Then remove the split wood and move the riving

knife and therefore the log lifter back down.

• Now you can roll a new log onto the log lifter.

Resetting the log lifter

This is used as a second guard arm when not using

the trunk lifter or when automatic return is enabled.

For this, the arm is moved up until it locks in position

in the hook.

• Ensure that the tractor unit‘s speed does not ex-

ceed the number on the rating plate, max. 540 per

min.

• Before maintenance work or if the riving knife is

jammed, rst disconnect the machine from the trac-

tor unit, after turning off the tractor unit.

Attaching the splitter to the tractor unit, Fig. 13 + 14

1. Reverse the tractor unit to the wood splitter. Posi-

tion the lower support arms close enough to the

kindling splitter‘s xing pins.

2. Activate the tractor unit‘s parking brake and turn

off the motor. Block the back wheels on both sides

with wedges or other suitable objects.

3. Remove the dust cover (1) and attach it to the

drive shaft protective cap (2).

4. Lower the bottom support arms onto the kindling

splitter‘s xing pins and secure them with the

locking pins (3).

5. Position the top support arm in the bracket and

align it with the bracket holes. Insert the hitch pin

to lock the top support arm in place.

• The transmission drive shaft end has a diam-

eter of 34.8 mm and a connection with 6 teeth

(Standard Category 1 PTO).

6. Push the drive shaft over the drive shaft end on

the transmission and tractor unit. Push down

the spring pins located on both ends of the drive

shaft. Push the drive shaft further over the drive

shaft ends until the spring pins jump out and the

teeth of the drive shaft end lock.

7. Aligning the drive shaft

Viewed from the top and the side of the shaft, the

drive shaft end on the kindling splitter (15) and the

drive shaft end on the tractor unit (16) have to be

aligned in parallel. The angle of the drive shaft

joints (α) must be as small as possible.

8. Secure the safety chain of the shaft drive on a

xed part of the kindling splitter and tractor unit to

prevent the safety device turning.

Check the running direction of the tractor unit‘s drive

shaft. If the splitting arm is not in the top position,

bring the splitting blade in the top position, using the

return bracket or handles. If the splitting arm is al-

ready in the top position, activate the splitting mecha-

nism by moving both levers down. This will move the

splitting arm down.

If the splitting blade does not move despite activation

of the handles or return bracket, stop the shaft drive

and change its direction.

Never let the shaft drive run in the wrong direc-

tion! This will inevitably destroy the pump sys-

tem and no warranty claim can be made.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HL3000GM in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 6.18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HL3000GM Manual

Product: