781960

Scheppach HL1350 Manual

25
Zoom out
Zoom in
Previous page
1/128
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 25
m IMPORTANT!


10. Initial operation
       

• 

• 
• 
• 
• The oil level.
• Functional check
Checking the oil level (Fig. 15)
         
oil pump and control valve. Check the oil level regu-
-
age the oil pump. The level of oil must be checked
when the riving knife is pulled back. If the oil level is
at the lower notch, then the oil level is at a minimum.
        
added. The upper notch indicates the maximum oil
level. The machine must be on level ground. Screw

E- Motor
Check the running direction of the motor. If the split-
ting arm is not in the top position, bring the splitting
blade in the top position, using the return bracket or
-

levers down. This will move the splitting arm down. If
the splitting blade does not move despite activation of
󰀨
machine. Turn the pole reversing unit in the plug-in
-
tion of the motor.
Never let the motor run in the wrong direction!
This will inevitably destroy the pump system and
no warranty claim can be made.
Functional test

Action: Result:
Push both handles
towards below.
Splitting knife goes down
to approx. 20 cm above
the table.
Let one handle loose,
then the other.
Splitting knife stops in the
desired position.
Press both handles or
return bow upwards
Splitting knife returns to
upper position
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, lm and small parts! There is a risk of
swallowing and su󰀨ocation!
9. Attachment / Before starting the
equipment
9.1 Attaching the wheel axle and the wheels
(enclosed accessories bag a1) (g. 3)
Slide the wheel axle through the holes on the bottom,
rear end of the splitter.
Fit the wheels onto the wheel axle and fasten each of
them with a split pin.
Then attach the wheel caps.
9.2 Putting the splitter into the work position
(Fig. 4, 5 + 6)
Connect the splitter to the mains. Observe the rota-

    



each of the pins with a spring split pin. After that, drive
the splitting blade to the top position and remove the
support.
You must store the support safely because it is
needed every time the splitter is transported.
9.3 Attaching the supporting arm (15) (Fig. 7)

9.4 Attaching the hook (D) (Fig. 8)
Fasten the retainer hook to the frame with two screws

9.5 Attaching the log lifter(Fig. 9)
Fasten the trunk lifter to the retaining lug with the

9.6 Attaching the additional wheel (Fig. 10)
Attach the transport wheel as shown in Fig. 10. Fas-

with the locking pin.
9.7 Moving the transport handle (5) to the trans-
port position (g. 11)

splitter and is fastened in the working position. Loos-


the position of the transport handle. See steps 1 - 3.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HL1350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HL1350 in the language / languages: English, German, French, Italian, Polish as an attachment in your email.

The manual is 6.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info