782058

Scheppach HF3000 Manual

6
Zoom out
Zoom in
Previous page
1/28
Next page
8 english françãis 9
• Insert adjusting bolt (2).
• Attach stop track (3).
2 carriage bolts M6 x 50
2 sheet metal spacers
2 washers 6 in diam.
2 wing nuts M6
• Insert folding stop into the stop track.
Final assembly hf 3000/tfe 30, Fig. F1/F2
(1) stop tube
(2) adjusting bolt
(3) stop track
(4) plate
(5) retaining strip
(6) bearing strip
• Insert stop tube into the pivoting drill hole of the slide
table.
• Insert carriage bolt M8 x 65 from above and tighten with
washer by hand.
• Insert adjusting bolt (2).
• Attach stop track (3).
2 carriage bolts M6 x 50
2 sheet metal spacers
2 washers 6 in diam.
2 wingnuts M6
• Insert folding stop into the stop track.
• Attach plate (4) and retaining strip (5) to the table.
2 carriage bolts M8 x 25
2 serrated washers 8.2 in dia.
2 hex nuts M8
• Push bearing strip (6) between plate (4) and retaining
strip (5) and tighten the hex nuts.
Work piece clamping device, Fig. G
• Insert the clamping bolt into the slide table and tighten.
1 serrated washer 8.2 in dia.
1 hex nut M8
• Choose the appropriate drill hole according to the
pivoting direction of the stop track.
• Fasten work piece clamping device to the clamping bolt
by hand.
Notes on operation
Angle correction work piece stop, Fig. L
After making a test cut, check the angle. Loosen the cap
nut to make the necessary adjustment. The adjusting nut
(1) can be turned to the required position by hand by
pushing back the stop tube slightly. Then retighten the
cap nut and make another test cut. Repeat the correction
procedure if necessary.
Fig. M
Guiding the work piece safely is a requirement for acci-
dent-free precision work. Use the work piece clamping
device properly.
• Insert work piece
• Set clamping device onto the bolt with lever in position
(1).
• Set clamping device onto work piece with lever in
position (2) and tighten the hand grip on the bolt.
• To clamp a work piece, bring the lever into position (3).
Maintenance
Your scheppach pusher slide is practically maintenance-
free.
• Occasionally apply a few drops of oil to the work piece
clamping device.
• Replace the cleaning brush if necessary.
• Keep the ball-bearing guide of the slide table free
of sawdust and dirt by cleaning to guarantee smooth
running.
The following details are required to allow correct and fast
processing of a spare parts order:
• Machine type
• Machine number
• Description, order number for spare part
• When ordering spare parts for electric equipment, the
date shown on the nameplate of motor and switch must
be quoted.
• Quantity of the required spare part
• Exact details of address and type of dispatch
Guarantee
This appliance is covered by a 12 month’s guarantee
• The guarantee covers only material and construction
faults. Faulty parts are replaced free of charge,
customers must carry out replacement work.
• We guarantee only original scheppach parts.
• The guarantee does not cover: Transport damage, wear-
ing parts, damage resulting from improper use or failure
to observe operating instructions.
• Guarantee claims are valid only if no repairs have been
made by a third party.
• The warranty certicate is only valid with the invoice.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HF3000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HF3000 in the language / languages: All languages as an attachment in your email.

The manual is 1.59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach HF3000

Scheppach HF3000 User Manual - English, German, Dutch, French, Italian - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info