Manual Scheppach Forsa 8.0 (page 22 of 60) (English, German, Finnish)

782260

Zoom out

Zoom in

1/60

17 english

Manufacurer:

Scheppach

Fabrikation von Holzbearbeitungsmaschinen GmbH

Günzburger Straße 69

D-89335 Ichenhausen

General Instructions

• Check all parts for possible damage after unpacking.

Inform the shipper immediately if any damage has

occurred.

• Later claims will not be accepted.

• Check that the shipment is complete.

• Read the operating instructions to familiarize yourself

with the machine before use.

• Use only genuine accessories, wearing and spare parts.

Spare parts are available from your local authorized

dealer.

• When ordering be sure to include the article number and

model and year of manufacture of the machine.

NOTE:

The manufacturer of this machine shall not be held liable for

damage to this machine or resulting from use of this machine

which result from:

• improper use

• noncompliance with the operating instructions

• repairs made by unauthorized third parties / technicians

• installation and replacement of spare parts other than

genuine scheppach spare parts

• operation which does not comply with the conditions for

"proper use"

• power failures in the electric power supply system,

noncompliance with applicable electric regulations and

VDE requirements 01 00, DIN 57113 / VDE 01 13.

We recommend that you:

Read the full text of the operating instructions before assembly

and initial operation of this machine.

These operating instructions will help you to become

familiar with this machine and tell you how to use it

properly.

The operating instructions contain important information

on how to operate this machine in a safe, professional and

money saving manner, how to prevent hazards, save repair

costs, reduce down times and increase the reliability and

service life of this machine.

You must comply with local and national regulations which

apply to the operation of this machine in addition to the

safety instructions contained in the operating

instructions.

The operating instructions should be kept in a plastic cover

to protect against dirt and moisture and stored in close

proximity to the machine. Each person who operates the

machine must read the operating instructions before

operating the machine and follow these instructions

carefully. Only persons who have been trained in the use of

this machine and instructed on the hazards associated

with it may operate this machine. The required minimum

age must be complied with.

In addition to the safety instructions provided in these

operating instructions and applicable local and national

regulations please follow generally recognized technical

rules for the operation of wood cutting machines.

Table of contents

General Instructions 16

NOTE: 16

Summary of contents 16

Safety instructions 16

Proper Use 17

Additional Hazards 17

Special accessories 17

Special accessory sawblades 17

Noise Characteristics 19

Assembly 19

Initial Operation 20

Maintenance 21

Electrical Connection 22

EG-Konformitätserklärung 54

Guarantee 56

Warranty 56

This symbol is used throughout these operating instructions to

indicate instructions which effect safety:

Safety instructions

• Provide the safety instructions to every person who uses

this machine.

• Use the machine in perfect technical condition only in a

safe and careful manner which complies with the proper

use described in the operating instructions! Immediately

remedy any faults which could effect safety!

• Only tools which comply with European Standard EN

847-1 may be used.

• Follow all safety and danger instructions listed on the

machine.

• All safety and danger instructions on the machine must

be kept fully legible.

• Never use the panel sizing circular saw to cut ﬁrewood.

• Caution during use: the rotating cutting tool could cause

injury to ﬁngers and hands.

• Check power supply connections. Do not use damaged

electrical cords.

• Make sure that the machine has been placed on a hard

surface in a level and stable position.

• Keep children away from the machine when it has been

connected to the power supply.

• Machine operators must be at least 18 years old.

Trainees must be at least 16 years old but may operate the

machine under supervision only.

• Do not distract persons using the machine.

• Keep the working area around the machine free of

shavings and waste wood.

• If a second person is assigned to assist the machine

operator by removing ﬁnished workpieces from the panel

sizing circular saw the machine must be equipped with

a table length extension. The second person should not

stand any place other than at the output end of the table

length extension.

• Use only saw blades which are well sharpened and free

of cracks and deformities.

• Use of circular saw blades made of super speed steel is

prohibited.

• Machine safety equipment should not be detached or

disabled under any circumstances.

• The riving knife is an important safety device which

guides the workpiece and prevents the cutting joint from

closing behind the saw blade and the workpiece from

being kicked backwards. Check the riving knife thickness

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Forsa 8.0 in the language / languages: English, German, Finnish as an attachment in your email.

The manual is 9.46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Forsa 8.0 Manual

Product: