781654
31
Zoom out
Zoom in
Previous page
1/148
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 31
14. Troubleshooting
Warning:
Turn switch off and always remove plug from the power source before trouble shooting.
Fault Problem Solution
Quill returns too slowly or too quickly Spring has improper tension Adjust spring tension. See "Quill
return spring".
Chuck wiII not stay attached to
spindle. It falls off when trying to
install.
Dirt, grease or oil on the tapered inside
surface of the chuck or on the spindle's
tapered surface.
Using household detergent, clean
the tapered surfaces of chuck and
spindle to remove all dirt, grease and
oil. See "Installing the chuck".
Noisy operation 1. Incorrect belt tension 1. Adjust belt tension. See "Choosing
speed and belt tensioning".
2. Dry spindle. 2. Test and lubricate spindle. See
"Lubrication"
3. Loose spindle pulley 3. Check tightness of retaining nut on
pulley, and tighten if necessary
4. Loose motor pulley. 4. Tighten set screw in motor pulley
Wood splinters on underside. No "backup material" behind work piece. Use "backup material". See
"Positioning table and work piece".
Workpiece tom loose from hand. Not supported or clamped property. Support work piece or clamp it.
Drill bit bums. 1. Incorrect speed. 1. Change speed. See "Choosing
speed and belt tensioning".
2. Chips not coming out of hole. 2. Retract drill bit frequently to
remove chips.
3. Dull drill bit 3. Resharpen drill bit.
4. Feeding too slowly 4. Feed fast enough ta allow drill bit
to cut.
Drill leads off or hole not round. 1. Hard grain in wood or lengths of
cutting lips and/or angle not equal 1. Resharpen drill bit correctly.
2. Bent drill bit. 2. Replace drill bit.
Drill bit binds in work piece. 1. Work piece pinching drill bit or
excessive feed pressure. 1. Support work piece and clamp it.
See "Positioning table and work
piece".
2. Improper belt tension. 2. Adjust belt tension. See "Choosing
speed and belt tensioning".
Excessive drill bit run- out or wobble. 1. Bent drill bit 1. Use a straight drill bit.
2. Heavy wear of spindle bearings 2. Replace bearings.
3. Drill bit not properly installed in chuck. 3. Install drill properly. See "Installing
drill bits".
4. Chuck not properly installed. 4. Install chuck properly. See
"Installing the chuck".
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DP19Vario at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DP19Vario in the language / languages: English, German, French, Italian, Polish as an attachment in your email.

The manual is 7.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info