782073

Scheppach DM460T Manual

14
Zoom out
Zoom in
Previous page
1/108
Next page
14 english
Such defective electrical connection cables must not
be used as the insulation damage makes them ex-
tremely hazardous.
Check electrical connection cables regularly for dam-
age. Make sure the cable is disconnected from the
mains when checking.
Electrical connection cables must comply with the
regulations applicable in your country.
Single-phase motor, Fig. 06
• The mains voltage must coincide with the voltage
specied on the motor’s rating plate.
• Extension cables up to a length of 25 m must have a
cross-section of 1.5 mm2, and beyond 25 m at least
2.5 mm2.
• The connection to the mains must be protected with
a 16 A slow-acting fuse.
Only a qualied electrician is permitted to connect the
machine and complete repairs on its electrical equip-
ment.
In the event of enquiries please specify the following
data:
• Motor manufacturer
• Type of current of the motor
• Data recorded on the machine’s rating plate
• Data recorded on the switch’s rating plate
If a motor has to be returned, it must always be dis-
patched with the complete driving unit and switch.
Maintenance
• Overhauls, maintenance work, cleaning, as well as
the elimination of any malfunctions must only be un-
dertaken after turning off the motor.
• All protective and safety equipment must be rein-
stalled immediately upon completion of any repair
or maintenance work.
• Clean and lightly oil the spindle thread of the tool
holder when changing tools.
• When possible, the tail stock sleeve should be re-
moved by unscrewing it, cleaned and then sprayed
with a dry lubricant. Grease the threaded spindle.
• Check the eccentric clamp of the tailstock as well as
the tool holder and adjust if necessary. In addition,
tighten the hex nut under the bracket.
• Check the drive belt and replace when necessary.
Accessories
Article Art. No.
Turning lathe extension 4902301701
Additional tools 5er set 88002716
Additional tools 6er set 88002717
Screw chuck 7400 7200
Socket chuck Ø 30 mm 7400 8600
Socket chuck Ø 40 mm 7400 7300
Socket chuck Ø 60 mm 7400 8700
Driver plate Ø 80 mm 7400 8800
Three-jaw chuck Ø 100 mm 7400 8900
Four-jaw chuck Ø 125 mm 7400 7400
Drill chuck 3 – 16 mm cone mandrel MK-2 7400
7700
You can nd other accessories in our current cata-
logue or at www.scheppach.com.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the follow-
ing parts are therefore also required for use as con-
sumables.
Wear parts*: Carbon brushes, v-belt
* Not necessarily included in the scope of delivery!
Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective com-
ponents must be disposed of as special waste. Ask
your dealer or your local council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must
not be disposed of together with domestic
waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical and
electronic equipment (WEEE). This product must be
disposed of at a designated collection point. This can
occur, for example, by handing it in at an authorised
collecting point for the recycling of waste electrical
and electronic equipment. Improper handling of waste
equipment may have negative consequences for the
environment and human health due to potentially haz-
ardous substances that are often contained in electri-
cal and electronic equipment. By properly disposing
of this product, you are also contributing to the effec-
tive use of natural resources. You can obtain informa-
tion on collection points for waste equipment from
your municipal administration, public waste disposal
authority, an authorised body for the disposal of
waste electrical and electronic equipment or your
waste disposal company.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DM460T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DM460T in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 4.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info