781463
22
Zoom out
Zoom in
Previous page
1/132
Next page
22 GB
Fault Possible causes Action
Saw blades break Tension incorrectly set Set the correct tension
Load to great Feed the workpiece more slowly
Incorrect saw blade variety Use the correct saw blades
Workpiece not fed straight Avoid exerting pressure from the side
Motor does not function Mains Gable faulty Change faulty parts
Motor faulty Call customer service. Do not attempt to
repair the motor yourself as this should be
carried out by trained personnel.
Vibration
NOTE: The saw vibrates slightly
when the motor is running in normal
operation.
Saw incorrectely installed Refer to the instructions given earlier in
this manual for information on installing
the saw
Unsuitable underlay The heavier the work bench is,the less the
vibration. A bench made from ply wood
always vibrates more than one made from
solid wood. Select the work bench best
suited to your working conditions
The work bench is not screwed
down or is on the motor
Tighten the locking lever
The motor is not secured Securely screw the motor in place
Saw blade swings out
Holders not aligned straight
Holders not aligned Losen the screws with which the holders
are fastenedto the arm. Align the holders
so that they are perpendicular to each
other and retighten the screws.
Defective electrical connection cables
Electrical connection cables often suffer insulation
damage.
Possible causes are:
Pinch points when connection cables are run
through window or door gaps.
Kinks resulting from incorrect attachment or laying
of the connection cable.
Cuts resulting from running over the connecting
cable.
Insulation damage resulting from forcefully pulling
out of the wall socket.
Cracks through aging of insulation.
Such defective electrical connection cables must not
be used as the insulation damage makes them ex-
tremely hazardous.
Check electrical connection cables regularly for dam-
age. Make sure the cable is disconnected from the
mains when checking.
Electrical connection cables must comply with the
regulations applicable in your country.
Single-phase motor
The mains voltage must coincide with the voltage
specied on the motor’s rating plate.
Extension cables up to a length of 25 m must have
a cross-section of 1.5 mm2, and beyond 25 m at
least 2.5 mm2.
The connection to the mains must be protected
with a 16 A slow-acting fuse.
Only a qualied electrician is permitted to connect
the machine and complete repairs on its electrical
equipment.
In the event of enquiries please specify the following
data:
Motor manufacturer
Type of current of the motor
Data recorded on the machine’s rating plate
Data recorded on the switch’s rating plate
If a motor has to be returned, it must always be dis-
patched with the complete driving unit and switch.
12. Disposal and recycling
The equipment is supplied in packaging to prevent
it from being damaged in transit. The raw materials
in this packaging can be reused or recycled. Never
place batteries in your household refuse, in re or in
water. Batteries should be collected, recycled or dis-
posed of by environment-friendly means. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective
components must be disposed of as special waste.
Ask your dealer or your local council.
13. Troubleshooting
Warning: In the interests of operational safety, al-
ways switch off the saw and remove the mains plug
before carrying out maintenance work.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DECO-XL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DECO-XL in the language / languages: English, German, Dutch, French, Italian, Polish, Finnish as an attachment in your email.

The manual is 4.38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info