781464
29
Zoom out
Zoom in
Previous page
1/108
Next page
29
Troubleshooting table
Warning: In the interests of operational safety, always switch off the saw and remove the mains plug before carrying out
maintenance work.
Fault Possible causes Action
Saw blades break Tension incorrectly set Set the correct tension
Load to great Feed the workpiece more slowly
Incorrect saw blade variety Use the correct saw blades
Workpiece not fed straight Avoid exerting pressure from the side
Motor does not function Mains Gable faulty Change faulty parts
Motor faulty Call customer service. Do not attempt
to repair the motor yourself as this
should be carried out by trained
personnel.
Vibration
NOTE: The saw vibrates slightly
when the motor is running in normal
operation.
Saw incorrectely installed Refer to the instructions given earlier
in this manual for information on
installing the saw
Unsuitable underlay The heavier the work bench is,the
less the vibration. A bench made from
ply wood always vibrates more than
one made from solid wood. Select
the work bench best suited to your
working conditions
The work bench is not screwed down
or is on the motor
Tighten the locking lever
The motor is not secured Securely screw the motor in place
Saw blade swings out
Holders not aligned straight
Holders not aligned Losen the screws with which the
holders are fastenedto the arm.
Align the holders so that they are
perpendicular to each other and
retighten the screws.
Plan de recherche des défauts
Avertissement: Dans I‘intérêt de la sécurité du service, éteignez toujours la scie et retirez la prise de contact avant
d‘entreprendre des travaux de réparation.
Défaut Origine possible Manière de procéder
Les lames se cassent Tension mal réglée Régler la tension convenable
Charge trop forte Amener la pièce d‘œuvre plus
lentement
Type de lame incorrect Utiliser les lames convenables
Piece d‘ouvrage amenée de travers Éviter une pression latérale
Le moteur ne marche pas Câble de réseau Remplacer les pièces défectueuses
défectueux
Moteur défectueux Appeler te service clientèle. N‘essayez
pas de réparer le moteur vous même,
ceci doit être effectué par une main
d‘œuvre spécialisée autorie
Vibration
REMARQUE: La scie vibre un peu
tourne.
Scie mal montée Pour le montage de la scie, voir les
indications plus haut dans le manuel
Table inconvénient Plus la table d‘ouvrage est lourde, plus
la vibration est faible. Une table en
presspahn vibre toujours plus qu‘une
table en bois massif. Choisissez la table
qui convient à votre avis
Table d‘auvrage mal vissée au appuyée
cantre le mateur
Tirer le levier de blocage
Moteur mal vissé Fixations non mises
en place
Bien visser le moteur
La lame de scie n‘oscille pas.
Orientation de travers
Desserrez les vis avec lesquelles les
fixations sont fixees au bras
Mettez les fixations en position
verticale. Resserrez les vis.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Deco Flex at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Deco Flex in the language / languages: English, German, French, Italian, Polish, Finnish as an attachment in your email.

The manual is 2.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info