781464

Scheppach Deco Flex Manual

25
Zoom out
Zoom in
Previous page
1/108
Next page
25
m Raccordement électrique
Le moteur électrique qui est installé est raccordé en ordre
de marche. Le raccordement électrique que doit effectuer
le client ainsi que les cables de rallonge utilisés doivent
correspondre aux normes en vigueur.
REMARQUES IMPORTANTES
En cas de surcharge du moteur, celui-ci s’arrête auto-
matiquement. Après un temps de refroidissement (d’une
durée variable), il est possible de remettre le moteur en
marche.
CÂBLES DE BRANCHEMENT ÉLECTRIQUE
DÉFECTUEUX
Il arrive fréquemment que l’isolation des câbles de bran-
chement électrique présente des avaries.
Les causes en sont:
• Écrasements, si le câble passe sous la porte ou la
fenêtre.
• Coudes dûs à une mauvaise fixation ou un mauvais
guidage du câble de branchement.
• Coupures dues à un écrasement du câble.
• Extractions violentes du câble de la prise murale.
• Fissures dues au vieillissement de l’isolation.
Il est déconseillé d’utiliser des câbles électriques qui
présentent ces types d’avaries. Danger de mort.
Vérifier régulièrement les câbles de branchement élec-
trique. Veiller à ce que le câble n’entre pas en contact
avec la tension de secteur pendant la vérification.
Les câbles de branchement électrique doivent corres-
pondre à la réglementation en vigueur dans votre pays.
MOTEUR MONOPHASÉ
• La tension du secteur doit correspondre aux indications
portées sur la plaque signalétique du moteur.
• Les câbles de rallonge d’une longueur maximale de 25
m doivent présenter une section transversale de 1,5
mm2, ceux d’une longueur supérieure à 25 m doivent
présenter une section transversale de 2,5 mm2.
• Le branchement au réseau est équipé d’un fusible à
action retardée de 16 A.
Les raccordements et les réparations de l’installation
électrique ne doivent être effectuées que par un élec-
tricien.
En cas de questions supplémentaires, veuillez fournir les
indications suivantes:
• Fabricant du moteur
• Nature du courant du moteur
• Données se trouvant sur la plaque signalétique de la
machine
• Données se trouvant sur la plaque signalétique du
conjoncteur
En cas de renvoi du moteur, toujours envoyer l’unité
moteur complète avec le conjoncteur.
m Electrical connection
The installed electric motor is completely wired ready
for operation.
The customer’s connection to the power supply system,
and any extension cables that may be used, must con-
form with local regulations.
IMPORTANT REMARK:
The motor is automatically switched off in the event of
an overload. The motor can be switched on again after a
cooling down period that can vary.
DEFECTIVE ELECTRICAL CONNECTION CABLES
Electrical connection cables often suffer insulation dam-
age.
Possible causes are:
• Pinch points when connection cables are run through
window or door gaps.
• Kinks resulting from incorrect attachment or laying of
the connection cable.
• Cuts resulting from running over the connecting cable.
• Insulation damage resulting from forcefully pulling out
of the wall socket.
• Cracks through aging of insulation.
Such defective electrical connection cables must not be
used as the insulation damage makes them extremely
hazardous.
Check electrical connection cables regularly for damage.
Make sure the cable is disconnected from the mains
when checking.
Electrical connection cables must comply with the regu-
lations applicable in your country.
SINGLE-PHASE MOTOR
• The mains voltage must coincide with the voltage
specified on the motor’s rating plate.
• Extension cables up to a length of 25 m must have a
cross-section of 1.5 mm2, and beyond 25 m at least
2.5 mm2.
• The connection to the mains must be protected with a
16 A slow-acting fuse.
Only a qualified electrician is permitted to connect the
machine and complete repairs on its electrical equip-
ment.
In the event of enquiries please specify the following
data:
• Motor manufacturer
• Type of current of the motor
• Data recorded on the machine’s rating plate
• Data recorded on the switch’s rating plate
If a motor has to be returned, it must always be dis-
patched with the complete driving unit and switch.
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Deco Flex at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Deco Flex in the language / languages: English, German, French, Italian, Polish, Finnish as an attachment in your email.

The manual is 2.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info