782186
11
Zoom out
Zoom in
Previous page
1/92
Next page
12 english
the bench and guide the saw blade pins into the recess.
Repeatthisprocedurefortheupperbladeholder.Push
the upper arm of the saw slightly downwards before
tighteningthescrews(Fig.9,10,13).
2Checkthepositions ofthe bladepins in both holders
(Fig.12).
3Tensionthebladeusingthetensioningtap.Checkthe
bladetension.Carryonturningclockwisetotensionthe
bladefurther(Fig.11).
Note: It is difficult to open the tensioning tap again if the blade
is too tightly tensioned.
Basic operation
Ascrollsawisfundamentallya„curvecuttingtool“but
which can also carry out straight and angled edge cuts. Fa-
miliarise yourself with the following important points prior
to commissioning the saw.
• Thesawdoesnotautomaticallycutwood.Youmustfeed
the wood against the saw blade manually.
• ThecuttingprocessoccursonIywhilethebladeismov-
ing downwards.
• Feedthewoodslowlyagainstthesawbladeasthesaw
blade teeth are small and cut only while moving down-
wards.
• AlIpersonscarryingoutworkwiththesawrequiretrain-
ing. The saw blade may break easily during this train-
ing time Iwhile the operator is sti1l unfamiliar with the
saw.
• Thesawisbestsuitedtorsheetsofwoodlessthan2.5
cm thick.
• Feedthewoodespeciallyslowlyagainstthebladeand
avoid abrupt curves to prevent the saw blade from break-
ing, if you wish to cut wood sheets thickerthan 2.5 cm.
• Sawbladeteethbluntenovertime,sawbladesmustbe
replaced.Thesawbladesaresufcienttor1/2to2op-
erating time depending upon the type of wood.
• Tryandmakesurethatthesawbladefollowsthegrainof
the wood in order to obtain a clean cut.
• deco 402/decotronic: The saw speed must be reduced
to minimum when cutting precious and non-terrous met-
als.
Inside cuts
Warning: Switch off the saw and remove the mains supply plug
before installing saw blades in order to avoid injuries caused
by unintentional activation of the saw.
This saw is suited also to inside cuts cuts not starting at
the edge of the work piece. Proceed as follows:
• Drilla6mmholeintheworkpiece.
• Loosenthebladetensionerandreleasethetensionin
the blade.
• Placetheboreholeoverthesawbladeslotinthework
bench.
• Installthesawbladethroughtheholeintheworkpiece
and through the work blade slot, and fasten the blade to
the holders.
• Whenyouhavecompletedtheinsidecut,removethesaw
blade and then remove the workpiece from the bench.
m Electrical connection
The installed electric motor is completely wired ready for
operation.
The customer’s connection to the power supply system,
and any extension cables that may be used, must conform
with local regulations.
Important remark:
The motor is automatically switched off in the event of an
overload. The motor can be switched on again after a cool-
ing down period that can vary.
Defective electrical connection cables
Electrical connection cables often suffer insulation dam-
age.
Possible causes are:
• Pinch points when connection cables are run through
window or door gaps.
• Kinksresulting fromincorrect attachmentor layingof
the connection cable.
• Cutsresultingfromrunningovertheconnectingcable.
• Insulationdamageresultingfromforcefullypullingout
of the wall socket.
• Cracksthroughagingofinsulation.
Such defective electrical connection cables must not be
used as the insulation damage makes them extremely haz-
ardous.
Checkelectricalconnectioncablesregularlyfordamage.
Make sure the cable is disconnected from the mains when
checking.
Electrical connection cables must comply with the regula-
tions applicable in your country.
Single-phase motor
• Themainsvoltagemustcoincidewiththevoltagespeci-
edonthemotor’sratingplate.
• Extensioncablesuptoalengthof25mmusthavea
cross-section of 1.5 mm2, and beyond 25 m at least 2.5
mm2.
• Theconnectiontothemainsmustbeprotectedwitha
16 A slow-acting fuse.
Onlyaqualiedelectricianispermittedtoconnectthema-
chineandcompleterepairsonitselectricalequipment.
Intheeventofenquiriespleasespecifythefollowingda-
ta:
• Motormanufacturer
• Typeofcurrentofthemotor
• Datarecordedonthemachine’sratingplate
• Datarecordedontheswitch’sratingplate
If a motor has to be returned, it must always be dispatched
with the complete driving unit and switch.
m Maintenance
Warning: In the interests of operational safety, always switch
off the saw and remove the mains plug before carrying out
maintenance work.
General
Reapplicationofthewaxcoatingontheworkbenchmakes
feeding the workpiece to the blade easier.
Motor
The mains cable should be replaced immediately if pulled
out, cut or damaged in any other way.
Donotlubricatethemotorbearingsorinternalparts!
Saw arm bearings
Lubricate the saw arm bearings every 50 hours. Proceed
asfollows(Fig.14).
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Deco 402 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Deco 402 in the language / languages: All languages as an attachment in your email.

The manual is 2.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info