Manual Scheppach DBS800 (page 15 of 88) (English, German, Dutch, French, Italian, Polish, Spanish)

781682

Zoom out

Zoom in

1/88

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

GB І 15

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

3. Never use the safety devices for handling or

transporting purposes.

Maintenance

m Warning! Prior to any adjustment, maintenance

or service work disconnect the mains power plug!

General maintenance measures

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it

down with compressed air at low pressure.

• We recommend that you clean the equipment im-

mediately after you use it.

• Clean the equipment regularly with a damp cloth

and some soft soap. Do not use cleaning agents

or solvents; these may be aggressive to the plastic

parts in the equipment. Ensure that no water can

get into the interior of the equipment.

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the fol-

lowing parts are therefore also required for use as

consumables.

Wear parts*: grinding wheel, device fuse, clamping

chuck

* Not necessarily included in the scope of delivery!

Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from

dust and moisture.

Store the operating manual with the electrical tool.

Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions.

The customer‘s mains connection as well as

the extension cable used must also comply with

these regulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

If a drill bit does not look like this, it must be

milled.

Step 1 – Presetting

• Take the clamping chuck (4) and insert it in the set-

ting guide (3). (Fig. D)

• Open the clamping chuck (4) by turning to left un-

til the drill bit to be milled can be inserted in the

clamping chuck (4).

• Open the positioning jaws by pressing the clamping

button (2). The drill bit can now be pushed up to the

end stop between the positioning claws. (Fig. D)

• Slowly release the clamping button (2) so the clos-

ing positioning jaws grip the drill bit above the

clamping slot and thus position it. (Fig. E)

• Now close the clamping chuck (4) by turning to the

right and pull it out of the setting guide (3).

• Now retighten the clamping chuck (4) a little

Step 2 – Grinding

• Connect the drill bit sharpener to the mains supply.

• Switch on the drill bit sharpener at the On/Off

switch (12) (Fig.A).

• Insert the clamping chuck (4) with the drill bit

(clamped in step 1) into the milling guide (7). (Fig.

• Now turn the clamping chuck (4) under slight pres-

sure to the respective end stop to the right and left

until the grinding noise markedly decreases.

• Pull the clamping chuck (4) out of the milling guide

(7), rotate by 180° and repeat the grinding process.

• Switch off the drill bit sharpener at the On/Off

switch (12). Let the grindstone come to a halt before

taking off the clamping chuck (4).

• Make sure that the drill bit is correctly ground and

corresponds to the two or three points previously

mentioned for a sharp drill bit.

Step 3 – Pointing

• Insert the clamping chuck (4) with the drill bit

(clamped in step 1) into the clearance angle guide

(1). (Fig. G)

• Now turn the clamping chuck (4) under slight pres-

sure to the respective end stop to the right and left

until the grinding noise markedly decreases.

• Pull the clamping chuck (4) out of the clearance an-

gle guide (1), rotate by 180° and repeat the thinning

process.

• Switch off the drill bit sharpener at the On/Off

switch (12). Let the grindstone come to a halt before

taking off the clamping chuck.

• Make sure the drill bit is correctly pointed; this is

characterised by a sharp point in the middle of the

drill bit.

Transport

1. Turn off the power tool before any transport and

disconnect it from the power supply.

2. Protect the power tool from knocks, bumps and

strong vibrations, such as during transport in ve-

hicles.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DBS800 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3.75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach DBS800 Manual

Product: