781887

Scheppach DB2000 Manual

21
Zoom out
Zoom in
Previous page
1/36
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 21
• Keep safety devices, air vents and the motor hous-
ing as dust and dirt-free as possible.
• Clean the device with a clean cloth, or blow it out
with compressed air at low pressure.
• All moving parts are to be re-greased at periodic
intervals.
• Do not use detergents or solvents as these might
damage the plastic parts of the device. Make sure
that no water can get inside the device.
Carbon brushes
In case of excessive sparking, have the carbon brush-
es checked by a qualied electrician.
m CAUTION! The carbon brushes should be re-
placed only by a qualied electrician.
Check the oil level
The oil level should be checked before each use of
the device.
Place the device with the tool holder in the down
position on the oor. The oil must be at least 4 mm
above the bottom edge of the sight glass. Rell oil, if
required.
Oil change (Fig. E)
The oil should be changed after about 40-50 hours
of operation.
Recommended oil: 30 ml SAE 15W/40 or similar.
m CAUTION! Switch off the device. Disconnect
the mains plug!
1. Unscrew the sight glass (4) using the Allen wrench
(4) and drain the oil.
2. To prevent uncontrolled drainage of oil, place the
container under the drain plug and collect the oil
in it.
Note: Waste oil must be disposed of at the appro-
priate collection point for used oil!
3. Fill the new oil has reached (about 30 ml) into the
oil ller opening, until the oil level has reached the
specied level.
4. Tighten the sight glass again.
5. Check the oil level again after a short period
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Chisel, carbon brushes
* Not necessarily included in the scope of delivery!
AC motor
• The mains voltage must be 230 V~ / 50 Hz
• Extension cables up to 25 m length must have a
cross section of 1.5 mm2.
Power supply and extension cord must be 3-wire = P
+ N + SL. - (1/N/PE).
The mains supply is secured up to 16 A.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection condi-
tions. This means that use of the product at any
freely selectable connection point is not allowed.
• Given unfavourable conditions in the power supply
the product can cause the voltage to uctuate tem-
porarily.
• The product is intended solely for use at connec-
tion points that
a) do not exceed a maximum permitted supply im-
pedance “Zmax”, or
b) have a continuous current-carrying capacity of
the mains of at least 100 A per phase.
• As the user, you are required to ensure, in consulta-
tion with your electric power company if necessary,
that the connection point at which you wish to oper-
ate the product meets one of the two requirements,
a) or b), named above..
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Motor data - type plate
13. Maintenance
If personnel qualied for unusual maintenance tasks
or repairs must be obtained during of after the war-
ranty period, please always contact a service point
recommended by us or contact the manufacturer.
• Only perform repair, maintenance and cleaning
work as well as the correction of malfunctions with
the drive switched off as a basic rule.
• All protective and safety equipment must be reas-
sembled immediately after repair, maintenance is
completed.
Cleaning
m CAUTION! Disconnect the mains plug.
• Clean the machine each time after completing
work.
• The machine should be cleaned reg-
ularly to remove dust and dirt.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach DB2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach DB2000 in the language / languages: English, German, French as an attachment in your email.

The manual is 1.89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info