782042
36
Zoom out
Zoom in
Previous page
1/160
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
36 | GB
Trimming (Fig. I)
Attention: Leave stubs in branches or below cut
       
above shoulder height. Leave such work to an expert.

limb.
       
through the branch. The third section (item 3) is
  
branch at 2.5 to 5 cm from the trunk.
Sawing on a slope (Fig. K)
        
stand higher than the tree trunk (Fig. K). In order to
maintain complete control at the moment of “sawing
through”, reduce pressure towards the end of the

of the chainsaw.
Warning!: The saw chain must not come in contact
with the ground..
After completing the cut, wait for the saw chain to
come to a standstill before removing the chainsaw.
  󰀨     
from one tree to the next.
10. Maintenance


Keep the cooling vents on the motor housing clean
and unobstructed at all times.
      
      

Customer Service.
          

Should the chainsaw fail despite our careful
manufacturing and inspection procedures, have it

shop.
Filling in chain oil
To prevent dirt getting inside the tank, clean the oil
tank cap (21) before opening. Check the contents of
     
         

Sharpening the saw chain
        
    
also obtain chain sharpening equipment to enable

Please follow the corresponding operating
instructions.
   

Follow the maintenance regulations and the
instructions for changing tools
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the
following parts are therefore also required for use as
consumables. Wear parts*:
Saw chain
Guide bar
Chain oil
Carbon brushes
Claw stop

11. Storage
      
chain guard.

of children.
When the device is not being used, store it so it

Warning!
Do not store the device without protection outside or
in a damp environment.
12. Electrical Connection

to work. The connection complies with the relevant
VDE and DIN regulations.
      
extension line must meet these regulations.
The product meets the requirements of EN
61000-3-11 and is subject to special connection
conditions. This means that use of the product
       
allowed.

       


points that
       
impedance “Z, or
  
the mains of at least 100 A per phase.
        
      

wish to operate the product meets one of the two
requirements, a) or b), named above.
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach CSE2700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CSE2700 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 8.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info