782042
32
Zoom out
Zoom in
Previous page
1/160
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
32 | GB
The running direction is marked with an arrow on the



upwards and put on the saw chain (4, beginning at the
tip of the bar.
Then assemble the guide bar with the saw chain as
follows:
Place the guide bar with the saw chain on the chain
wheel (16) and guide bolt (17).
Place the saw chain round the chain wheel (16).
Cause the chainsaw to the sprocket and check


the lock nut (5).

Tensioning the saw chain
Warning!



Make sure the saw chain (4) is inside the guide
groove of the guide bar (7).
Turn the knob (Fig. 3/5a) clockwise until the saw

When cold, it should be possible to lift the chain in
the middle of the guide bar approx. 5 mm.
When warm, the saw chain will expand and slacken
        󰀨  

If the saw chain is re-tensioned when hot, it must
be loosened again when the sawing work has been
completed.
Otherwise, the contraction which takes place as
       
tension.
A new saw chain requires a running-in period of
      
important at this stage. After running in, check

8. Initial operation


      

Check also that the chain lubrication and the oil
gauge are in good working order (see Fig. 4). When
the oil lever is approx. 5 mm from the bottom mark,


Switch on the chain saw and hold it above the ground.
Be careful not allow the chainsaw to touch the ground.


      


Customer Service. (Be sure to read the section
Filling in chain oil and chain lubrication” on this
point).

(see the section “Tensioning the saw chain” on this
point).

also the section “Releasing the chain brake”).
To switch on:
Release the chain brake (3), push in the lock (11)
and press the power switch (13).
Place the lowest claw (Fig 2, J) on the wood . Raise

wood. Move the chain saw back a little and place
the claw further down.
Be careful when sawing splintered wood as pieces
󰀨

at high speed .
To switch o󰀨
Release either the ON/OFF switch (13) on the rear
grip.
The release of ON/OFF switch results the stop of
      
This is normal and safe for the proper operation of
the chainsaw.

Clean the saw chain and guide bar and replace the
chain guard.
If the chain brake is activated the chainsam will be

Explanation of the operation indicator (Fig. 2, 18):
Green LED:
The green LED comes on when the device is in use.
9. Working instructions
Transporting the chainsaw
     
the plug from the power socket and slide the chain
guard over the rail and chain. If several cuts are to
be performed with the chain saw, the saw must be
󰀨
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach CSE2700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CSE2700 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 8.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info