782591

Scheppach CSD40-20Li Manual

23
Zoom out
Zoom in
Previous page
1/88
Next page
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58 www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
23 | GB
be opened simply by turning it . After you have in-
serted the required bit and xed it in place by turning
the chuck , you can immediately continue working.
The spindle lock releases itself automatically when
the motor is started (by operation of the ON / OFF
switch 3 ).
Torque pre-selection
You can adjust the torque by using 14 torque prese-
lection.
Select a low setting for small screws, soft workma-
terial.
Select a high setting for large screws, hard work ma-
terials and for the extraction of screws.
For drilling, push the selector to the setting for drill-
ing, in that you adjust the torque pre-selector
to the position .
For drilling tasks, also push the gear selector switch
1 to the front (Position: 2).
2 Gear Drive
CAUTION! Move the gear selector switch 1 only after
the device has come to a standstill.
Failure to observe this advice may result in damage
to the device.
In the rst gear (Gear selector switch 1 in Position: 1)
A speed of up to approx. 400 rpm can be achieved
and a high torque. This setting is intended for use
with all screwing tasks and for accessories (see ex-
ample Fig. B).
In the second gear (Gear selector switch 1 in Posi-
tion: 2)
It achieves a speed of up to approx. 1400 rpm, for
the carrying out of drilling tasks (see example Fig. A).
Preparing the tool for use
Switching On /Off
Switching on:
To start the appliance squeeze on the ON / OFF
switch 3 and then keep it pressed down. The LED
working light 12 comes on with a slightly or fully
pressed ON /OFF switch 3 and illuminates the work-
ing area in poor lighting conditions.
Switching off:
To stop the appliance, release the ON
Adjusting the speed
The ON / OFF switch 3 has a variable speed control
device. Slight pressure on the ON / OFF
switch 3 will cause the rotation speed to slow down.
With increased pressure, the rotational speed will in-
crease.
Note: The integrated engine brake means that the
device will come to a fast standstill.
Switching direction of rotation
To switch the direction of rotation, push the direction
of rotation switch 2 to either the
right or to the left.
Tips and Tricks
Before you use the appliance, check to see that the
screw or drill bit is properly tted, i.e.
located centrally in the chuck.
Screw bits are designated with their dimensions and
their shape. If you are unsure, always try
the particular screw bit out to see whether it sits in
the screw head without any free play.
Torque:
Smaller screws and bits in particular can be easily
damaged if you adjust the appliance with too high a
torque and/or rotation speed.
Hard screwdriving conditions (into metal):
Particularly high torques can occur, for example with
metal screws tightened by socket tool bits.
Select a lower rotation speed.
Soft screwdriving conditions (e.g. into soft wood):
You should also select a low speed in order not to
damage the wood workpiece surface through con-
tact with the metal screw head.
Use a countersinker.
When drilling into wood, metal and other materials,
take note of the following advice:
With small diameter drill bits use a high drill speed.
For large diameter drill bits, use a low drill speed.
For hard materials, select a low drill speed.
For soft materials, select a high drill speed.
Secure or x down the workpiece (if possible) in a
clamp or vice.
Mark the intended position of the hole with a centre
punch or a nail and select a low drill speed
for drilling.
Take the rotating drill bit out of the hole frequently so
that swarf or drill dust can be re-moved and
the hole and tool is ventilated.
Drilling in metal:
Use a metal drill bit (HSS). For the best results, you
should cool the bit with oil. Metal drill bits
can also be used to drill into plastic.
Drilling in stone:
Use a circular shafted masonry drill bit with a hard-
ened metal tip.
Drilling in wood:
Normally you should use a wood drill with a centring
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach CSD40-20Li at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach CSD40-20Li in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 4.61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info