782108

Scheppach C6 06 Woodster Manual

13
Zoom out
Zoom in
Previous page
1/160
Next page
13
dB
Marche à vide LpAeq = 69,0 dB(A)
Traitement LpAeq = 78,5 dB(A)
Les valeurs d’émission s’entendent avec un supplément
d’imprécision de mesure de K = 4 dB
Caractéristiques de bruit / fraiseuse de table
Caractéristiques de bruit selon EN 50144 :
Pression acoustique LpA = 100,5 dB(A)
Puissance acoustique LWA = 113,5 dB(A)
Valeur d’émission en dB par rapport aux postes de travail
Traitement LpAeq = 102,5 dB(A)
Les valeurs d’émission s’entendent avec un supplément
d’imprécision de mesure de K = 4 dB
Informations sur l’émission de poussières
Les valeurs d’émission de poussières mesurées selon les
«principes d’essai de l’émission de poussières (paramêtres
de concentration) en amont des machines d’usinage du
bois» du comité spécial ‘Bois’ sont inférieures à 2 mg/
m3. Lors du raccordement de la machine à une aspiration
correcte en service avec un débit d’air d’au moins 20 m/s,
cela permet de supposer l’observation sûre et durable de
la valeur limite TRK pour la poussière de bois applicable
en République Fédérale d’Allemagne.
Dans les présentes instructions d’utilisation tous les endroits
concernant votre sécurité ont été marqués par:
Consignes de sécurité
Transmettre les consignes de sécurité à toutes les personnes
travaillant sur la machine. Avant de commencer à travailler,
le personnel chargé des activités sur la machine doit avoir lu
les instructions d’utilisation, et en particulier le chapitre des
consignes de sécurité. Une fois le travail commencé il sera
trop tard. Cela s’applique en particulier pour les personnes
n’intervenant sur la machine qu’à l’occasion, par ex. pour
l’équipement, la maintenance.
• Observer toutes les consignes de sécurité et indications
de danger sur la machine.
• Toutes les consignes de sécurité et indications de danger
sur la machine doivent être conservées parfaitement
lisibles.
• Vérifier les conducteurs de raccordement au réseau.
Ne jamais utiliser des conducteurs de raccordement
endommagés.
• Veiller à ce que la machine soit placée de manière
stable sur un sol résistant.
• Veiller à un éclairage suffisant dans la zone de travail
et aux alentours de la machine.
• Attention pendant le travail : Risque de blessures
pour les doigts et les mains par les outils de coupe en
rotation.
• Tous les dispositifs de protection et couvercles doivent
être en place pendant le travail sur la machine.
• éloigner d’autres personnes, en particulier des enfants,
de la zone de travail et de la machine raccordée au
réseau ainsi que des conducteurs d’alimentation.
• Veiller à ce que les enfants n’aient aucun accès à la
machine non en service.
tolerance of K=4 dB.
Noise characteristics / Table shaper
Noise characteristic value according to EN 50144:
Sound pressure LpA = 100.5 dB(A)
Sound power LWA = 113.5 dB(A)
Work place influenced emission values in dB
Active work LpAeq = 102.5 dB(A)
For the given emission values there is a measurement
tolerance of K=4 dB.
Information for dust emission
According to the “basic regulations for control of dust
emissions (concentration parameters) for wood work-
ing machines” of the expert council for wood, the dust
emission values measured are less than mg/m3. Thus
the connect of the machine to an appropriate exhaust
extraction system with at least 20 m/s air movement
speed can achieve an ongoing secure environment ac-
cording to the TRK values for wood dust in the Federal
Republic of Germany.
In these instructions for use, we have marked those items
which refer to your security with this sign:
Safety information
Please pass this safety information on to all persons who
work with the machine. People who operate this machine
must have read the instructions for use and, in particular,
the chapter concerning safety information. Once they have
begun work, it is too late. This is especially the case for
personnel who only occasionally use the machine, for ex-
ample when the machine is to be equipped or maintenance
work carried out.
• Pay attention to all safety and danger information on
the machine.
• Keep all safety and danger information on the machine
complete and in a legible condition.
• Check the electrical lines. Do not use defective
electrical connections.
• See that the machine is firmly situated on a firm
ground.
• Make sure that there is adequate light in the work place
and near the machine.
• Take care when working: rotating cutting tools present
danger of bodily harm to fingers and hands.
• When the machine is in use, all protective equipment
and covers must be mounted.
• Keep all other people, especially children, away from
the work area and the machine when it is plugged in
as well as its cables.
• Make sure that children do not have access to the
machine when it is not in use.
• Do not overtax the equipment and use it only within
the performance parameters described in the technical
data section of the information for use.
• When working outdoors, make sure you can stand firmly
and have slip-proof shoes.
• Do not use the cable for uses other than that for which
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach C6 06 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach C6 06 Woodster in the language / languages: English, German, Dutch, Danish, French, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 6.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info