782108
9
Zoom out
Zoom in
Previous page
1/160
Next page
9
c6 06
Outils 6 / 8 mm
Réglage en hauteur de la
broche
0–42 mm
Vitesse 9000 tr/min
Perceuse de trous oblongs :
Dimension de table 260 x 125 mm
Zone du mandrin de per-
çage
13 mm
Perceuse de trou oblong 6 / 8 / 10 mm
Profondeur de perçage 45 mm
Mouvement vertical 60 mm
Mouvement transversal 95 mm
Poids 44 kg
Entraînement :
Moteur 230V / 50 Hz
Puissance 1000 watts
Protection moteur Oui
Déclenchement manque de
tension
Oui
Fiche Contact de protection
Sous réserve de modications techniques!
Caractéristiques de bruit selon EN ISO 3744.
Les valeurs indiquées sont des valeurs d’émission et
ne correspondent pas forcément aux valeurs réelles en
service.
Bien qu’il y ait une corrélation entre le niveau d’émission
et le niveau de nuisance, il n’est pas possible d’en déduire
de façon fiable, si certaine mesures de précautions
supplémentaires sont nécessaires ou non. Les facteurs
susceptibles d’influencer le niveau de nuisance sur le
poste de travail, comprennent la durée des nuisances,
les caractéristiques du local de travail, d’autres sources
de bruit etc., p. ex. le nombre de machines et d’autres
opérations ayant lieu dans le voisinage. Les valeurs
admissibles par poste de travail peuvent également
varier d’un pays à l’autre. Mais ces informations doivent
permettre à l’utilisateur de mieux évaluer les dangers et
les risques en présence.
Niveau de puissance acoustique en dB
Marche à vide LWA = 93 dB(A) pendant le rabotage
Marche à vide LWA = 92 dB(A) pendant le rabotage de
dégauchissage
Traitement LWA = 98 dB(A) pendant le rabotage
Traitement LWA = 99 dB(A) pendant le rabotage de
dégauchissage
Niveau de pression acoustique sur le poste de travail en
dB
Marche à vide LWA = 78 dB(A) pendant le rabotage
Marche à vide LWA = 82 dB(A) pendant le rabotage de
dégauchissage
Traitement LWA = 83 dB(A) pendant le rabotage
Traitement LWA = 91 dB(A) pendant le rabotage de
dégauchissage
Les valeurs d’émission s’entendent avec un supplément
d’imprécision de mesure de K = 3 dB
Informations sur l’émission de poussières
Les valeurs d’émission de poussières mesurées selon les
«principes d’essai de l’émission de poussières (paramètres
c6 06
Rotational speed 9000 1/min
Slot drill unit:
Table size 260 x 125 mm
Drill chuck width area 13 mm
Slot drill 6 / 8 / 10 mm
Drill depth 45 mm
Vertical movement 60 mm
Horizontal movement 95 mm
Weight 44 kg
Drive:
Motor 230V / 50 Hz
Capacity 1000 Watt
Motor protection yes
Power sag release yes
Plug Schuko (European standard
plug system, CEE 7/4)
Subject to technical
changes!
Noise characteristic values according to EN ISO 3744.
The given values are emission values and do not also pres-
ent safe working values. Although there is a correlation
between emission and nuisance levels, the relationship is
not dependable as an indicator as to whether additional
safety measures are necessary or not. Factors specific to
the workplace can influence the nuisance level, such as
the length of the activity, the characteristics of the work
room, other sources of noise, etc., for instance the num-
ber of machines and other nearby activities. Dependable
work place values can also vary from country to country.
This information should, nonetheless, allow a better es-
timation of possible dangers and risks.
Sound power levels in dB
Idling LWA = 93 dB(A) while planing
Idling LWA = 92 dB(A) while jointing
Active work LWA = 98 dB(A) while planing
Active work LWA = 99 dB(A) while joint planing
Sound pressure levels in the work place in dB
Idling LWA = 78 dB(A) while planing
Idling LWA = 82 dB(A) while joint planing
Active work LWA = 83 dB(A) while planing
Active work LWA = 91 dB(A) while joint planing
For the given emission values there is a measurement
tolerance of K=3 dB.
Information for dust emission
According to the “basic regulations for control of dust
emissions (concentration parameters) for wood work-
ing machines” of the expert council for wood, the dust
emission values measured are less than mg/m3. Thus the
connection of the machine to an appropriate exhaust ex-
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach C6 06 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach C6 06 Woodster in the language / languages: English, German, Dutch, Danish, French, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 6.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info