644521
15
Zoom out
Zoom in
Previous page
1/120
Next page
12 english
Maintenance
Warning: When servicing use only identical Ryobi replace-
ment parts. Use of any other parts may create a hazard or
cause product damage.
Warning: To avoid serious personal injury make sure the
belt/disc sander is turned OFF and the cord is unplugged
from the power source before performing any maintenance
or adjustment.
General maintenance
After using your belt/disc sander, clean it completely and
lubricate all sliding and moving parts. Apply a light coat of
automotive type paste wax to the worktable to help keep
the surfaces clean.
Motor housing
Frequently blow out any dust that may accumulate inside
the motor housing.
Changing drive belt, Fig. 20.
• Using a phillips head screwdriver, remove the two screws
in the center of the pulley cover.
Remove the cover.
Raise sanding belt to the vertical sanding position (see
Figure 20).
Next, loosen the hex head set screw. Raising the motor
pulley releases the belt tension.
Remove the old drive belt.
Fit the new drive belt on the drive pulley first and then
on the motor pulley.
• Test belt tension by squeezing the belt with your fin-
gers.
Adjust the belt tension with the hex head set screw until
there is about 1/4 in. (6 mm) of give.
Tighten the belt tension nut securely.
Note: Excessive tightness on the drive belt may cause in-
creased noise and overload the motor. Excessive looseness
on the drive belt may cause the drive belt to fail prema-
turely and make a severe chattering noise.
• Using a phillips head screwdriver, reinstall the pulley
cover and the two phillips head screws. Tighten secure-
ly.
Trouble shooting
Problem Possible Cause Help
Motor doesn’t start
a) ON/OFF switch damaged.
b) ON/OFF cable damaged.
c) ON/OFF relay damaged.
d) Fuse blown.
e) Motor burnt.
a-d) Replace all damaged parts before you
use your machine again.
e) Contact your local service centre. Every
attempt to carry out a repair, can be
dangerous if it is not done by skilled
personnel.
Machine gets slower
during work.
Too much pressure put on the workpiece.
Reduce the pressure on the workpiece.
Sanding belt comes off
the drive pulleys.
Belt does not run straight.
Reset the track.
The wood gets burnt
during sanding.
a) Sanding disc or belt covered with grease.
b) Excessive pressure on workpiece.
a) Replace disc or belt.
b) Reduce pressure on workpiece.
15


Need help? Post your question in this forum.

Forumrules
1

Forum

scheppach-bts800

Reset search

  • How do you change the sanding belt? I've released the tensioner but can't see how to get the bottom of the belt out. Submitted on 11-1-2019 at 17:50

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach BTS800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BTS800 in the language / languages: All languages as an attachment in your email.

The manual is 3,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info