782175

Scheppach BS3000 Primaster Manual

22
Zoom out
Zoom in
Previous page
1/44
Next page
22 GB
12 Avoid abnormal posture
–Make sure that you have secure footing and
always maintain your balance.
–Avoid awkward hand positions in which a sud-
den slip could cause one or both hands to come
into contact with the saw blade.
13 Take care of your tools
–Keep cutting tools sharp and clean in order to
be able to work better and more safely.
–Follow the instructions for lubrication and for
tool replacement.
–Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
–Check extension cables regularly and replace
them when damaged.
–Keep the handle dry, clean and free of oil and
grease.
14 Pull the plug out of the outlet
–Never remove loose splinters, chips or jammed
wood pieces from the running saw blade.
–During non-use of the electric tool or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
–When the saw blade is blocked due to abnormal
feed force during cutting, turn the machine off
and disconnect it from power supply. Remove
the work piece and ensure that the saw blade
runs free. Turn the machine on and start new
cutting operation with reduced feed force.
15 Do not leave a tool key inserted
–Before switching on, make sure that keys and
adjusting tools are removed.
16 Avoid inadvertent starting
–Make sure that the switch is switched off when
plugging the plug into an outlet.
17 Use extension cables for outdoors
–Only use approved and appropriately identied
extension cables for use outdoors.
–Only use cable reels in the unrolled state.
18 Remain attentive
–Pay attention to what you are doing. Remain
sensible when working. Do not use the electric
tool when you are distracted.
19 Check the electric tool for potential damage
–Protective devices and other parts must be
carefully inspected to ensure that they are fault-
free and function as intended prior to continued
use of the electric tool.
–Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and
all conditions must be fullled to ensure fault-
free operation of the electric tool.
–The moving protective hood may not be xed
in the open position.
–Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is speci-
ed in the operating manual.
–Damaged switches must be replaced at a cus-
tomer service workshop.
–Do not use any faulty or damaged connection
cables.
–Do not use any electric tool on which the switch
cannot be switched on and off.
20 Attention!
–The use of other insertion tools and other ac-
cessories can entail a risk of injury.
21 Have your electric tool repaired by a qualied
electrician
–This electric tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.
22 Do not use the cable for purposes for which it is
not intended Do not use the cable to pull the plug
out of the outlet. Protect the cable from heat, oil
and sharp edges.
Additional safety instructions
• Wear safety gloves whenever you carry out any
maintenance work on the blade!
• When cutting round or irregularly shaped wood, use
a device to stop the workpiece from twisting.
• When cutting boards in upright position, use a de-
vice to prevent kick-back.
• A dust extraction system designed for an air velocity
of 20 m/s should be connected in order to comply
with woodworking dust emission values and to en-
sure reliable operation.
• Give these safety regulations to all persons who
work on the machine.
• Do not use this saw to cut re wood.
• The machine is equipped with a safety switch to
prevent it being switched on again accidentally af-
ter a power failure.
• Before you use the machine for the rst time, check
that the voltage marked on the rating plate is the
same as your mains voltage.
• If you use a cable reel, the complete cable has to
be pulled off the reel.
• Persons working on the machine should not be dis-
tracted.
• Note the direction of rotation of the motor and blade.
• Never dismantle the machineʼs safety devices or put
them out of operation.
• Never cut workpieces which are too small to hold
securely in your hand.
• Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
• It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
• Note the information published by your professional
associations.
• Adjustable protective devices have to be adjusted
as close as possible to the workpiece.
• Important! Support long workpieces (e.g. with a roll-
er table) to prevent them sagging at the end of a cut.
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach BS3000 Primaster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BS3000 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 3.93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info