Manual Scheppach BS2000 Primaster (page 27 of 46) (English, German, French)

782174

Zoom out

Zoom in

1/46

27GB

8.10 Replacement of the table inlay

The table inlay (14) must be replaced if the slit en-

larges or is damaged.

1 For this purpose, disassemble the table from the

machine frame according to 8.1 in the opposite

direction.

2 Remove the table inlay from the sawing table by

pressing downwards.

3 Insert a new table inlay.

Mount the table top according to 8.1.

8.11 On/Off switch (Fig. 1)

• To turn the machine on, press the green button

„1“ (8).

• To turn the machine off again, press the red but-

ton „0“(8).

• The band saw is equipped with an undervoltage

switch. With a power failure, the band saw must

be switched back on again.

Attention!

When working with the machine, all protective devic-

es and guards must be tted.

The upper and lower bandwheel is protected by a

xed guard and an articulated cover. When opening

the cover, the machine is switched off. Starting is

possible only with closed cover.

9. Transport

The machine must only be lifted and transported on

its frame or the frame plate. Never lift the machine at

the safety devices, the adjusting levers, or the saw-

ing table.

During the transport the saw blade protection must

be in the lowest position and near the table.

Never raise at the table!

Unplug the machine from the mains during transport.

10. Working instructions

The following recommendations are examples of the

safe use of band saws. The following safe working

methods should be seen as an aid to safety. They

cannot be applied suitably completely or comprehen-

sively to every use. They cannot treat every possible

dangerous condition and must be interpreted care-

fully.

• Connect the machine to a suction unit when work-

ing in closed rooms. A suction device which con-

forms with commercial regulations must be used

for suction in commercial areas.

• Loosen the sawband when the machine is not in

operation (e.g. after nishing work). Attach a no-

tice on the tension of the saw band to the machine

for the next user.

• Collect unused sawbands and store them safely in

a dry place. Check for faults (teeth, cracks) before

use. Do not use faulty sawbands!

• Wear suitable gloves when handling sawbands.

• All protective and safety devices must be securely

mounted on the machine before beginning work.

• Never clean the sawband or the sawband guide

with a hand-held brush or scraper while the saw-

band is running. Resin-covered sawbands impair

working safety and must be cleaned regularly.

• For your own protection, wear protective glasses

and hearing protection. Wear a hairnet if you have

long hair. Roll up loose sleeves over the elbows.

• Always position the sawband guide as near the

workpiece as possible when working.

• Insure sufcient lighting in the work area and

around the machine.

• Always use the fence for straight cuts to keep the

workpiece from tipping or slipping away.

• When working on narrow workpieces with manual

feed, use the push stick.

• For diagonal cuts, place the saw bench in the ap-

propriate position and guide the workpiece on the

fence.

• Insure safe workpiece guidance.

• For arced and irregular cuts, push the workpiece

evenly using both hands with the ngers togeth-

er. Hold the workpiece with your hands on a safe

area.

• Use a pattern for repeated arced or irregular cuts.

• Insure that the workpiece does not roll when cut-

ting round pieces.

10.1 Rip fence (Fig. 7)

The rip fence serves as a guide during longitudinal

cuts.

• Clamp the longitudinal fence (5) in the desired po-

sition by pressing the clamping lever (M).

10.2 Angled cuts (Fig. 1, 5, 6, 14)

• In order to execute angled cuts parallel to the saw

band (Fig. 14), it is possible to tilt the saw bench

(6) forwards from 0° - 45°.

• Release the locking handle (F) (Fig. 5+6).

• Tilt saw bench (6) forwards, until the desired angle

is set on the degree scale. (Fig. 5+6)

• Retighten the locking handle (Fig. 5+6).

• Attention: With a tilted saw bench (6), the longitu-

dinal fence (5) must be positioned on the down-

ward facing side to the right of the saw band in

the working direction (Fig. 14) (if the workpiece

width allows this), in order to secure the workpiece

against slipping.

Attention! After every new setting, we recommend

performing a test cut, in order to check the dimen-

sional settings.

• With all cutting processes, the top band guide (4)

must be positioned as close as possible to the

workpiece.

• The workpiece must always be guided with both

hands and kept at against the band saw bench

(6), in order to prevent a jamming of the saw band.

• Forward feeding should always take place with an

even pressure, which is just sufcient for the saw

band to cut through the material with ease without

becoming blocked.

• Always use the longitudinal fence (5) for all cutting

processes that it can be used for.

• It is better to perform a cut in a single working

step than in multiple steps, which may require that

the workpiece be drawn back. However, if it is not

possible to avoid drawing the workpiece back then

the band saw must be switched off rst, and the

workpiece only drawn back once the saw band has

come to a standstill.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BS2000 Primaster in the language / languages: English, German, French as an attachment in your email.

The manual is 4.3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach BS2000 Primaster Manual

Product: