782113

Scheppach Bestcombi 5.0 Manual

35
Zoom out
Zoom in
Previous page
1/48
Next page
8.2
Operating deviations Shaper
Machine vibrates:
- Clamping levers for height and diagonal adjustment are not tightly screwed.
- Sawing tool is not tightly screwed.
Cuts are not clean/wood is burned:
- Sawing tool is dull
- Sawing tool is incorrectly mounted.
Rapid sawing tool wear:
- Sawing tool is incorrectly sharpened.
- Contaminated wood (cement, sand, nails).
Motor becomes too warm:
(It is too hot to touch with bare hands, it continuously shuts itself off.)
- By all means have a qualied electrician inspect the motor.
Machine comes to a stop:
- Overloading (feeding too rapid, sawing tool is dull).
Wood is raised by the rear side of the saw blade:
- Longitudinal limit stops are not parallel
- Splitting wedge is not aligned or crossing is too weak.
The spindle height is difcult to adjust:
- Thoroughly clean and lubricate the threaded rod, gears and slide tracks.
- Check the operation of the clamping lever.
Miscellaneous:
- Bearings make unusual noises: Inspect the bearings and replace if necessary.
- Check the tension of the V-belt (V-belts are accessible when the exhaust cover is removed).
8.1
Operating deviations Saw
Machine vibrates:
- Clamping levers for height and diagonal adjustment are not tightly screwed.
- Sawing tool is not tightly screwed.
Cuts are not clean/wood is burned:
- Sawing tool is dull
- Sawing tool is incorrectly mounted.
Rapid sawing tool wear:
- Sawing tool is incorrectly sharpened.
- Contaminated wood (cement, sand, nails).
Motor becomes too warm:
(It is too hot to touch with bare hands, it continuously shuts itself off.)
- By all means have a qualied electrician inspect the motor.
Machine comes to a stop:
- Overloading (feeding too rapid, sawing tool is dull).
Wood is raised by the rear side of the saw blade:
- Longitudinal limit stops are not parallel
- Splitting wedge is not aligned or crossing is too weak.
The spindle height is difcult to adjust:
- Thoroughly clean and lubricate the threaded rod, gears and slide tracks.
- Check the operation of the clamping lever.
Miscellaneous:
- Bearings make unusual noises: Inspect the bearings and replace if necessary.
- Check the tension of the V-belt (V-belts are accessible when the exhaust cover is removed).
8.0 Malfunctions
GB
8.3 Planer-thicknesser
Operating deviations
If your machine is maintained properly, it is unlikely that any problems will arise.
If the motor will not run:
- check the electrical system is switched on
- check that the machine is connected to the power supply
- drop in voltage (should be checked by a qualified electrician)
- Check the position of the vacuum exhaust sensor
When the machine tables are hard to adjust:
- grease the threaded rods, sliding surfaces, etc.
If the machine runs at an abnormally slow speed:
- the cutters are blunt
- depth of cut too great (adjust according to the hardness and width of the timber, and the condition of the cutters)
- drive rollers are dirty (clean them)
- table not clean or surface in a state of deterioration
- the drive belt is slipping
The machine vibrates:
- cutters are blunt or badly adjusted
- the cutters used are of different sizes (matching set only must be used)
- uneven floor mounting (adjust floor stand accurately)
The machine locks during planing:
- uncouple the drive
- switch off the motor
- remove cutter by lowering the planing table a little way
- reduce depth of cut and begin again, gradually reapproaching the planed depth
If a heel forms or the face is uneven after surfacing:
- the cutter is set higher than the exit table
- the workpiece is running incorrectly on the work tables
- see also “machine vibrates” 35
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Bestcombi 5.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Bestcombi 5.0 in the language / languages: English, German, French as an attachment in your email.

The manual is 6.33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info