Manual Scheppach BD9000 (page 8 of 12) (English, German)

644555

Zoom out

Zoom in

1/12

10 english

Keepworkareawelllighted.

• Keepchildrenaway.Allvisitorsshouldbekeptatasafe

distance from the work area.

• Makeyourworkshopkidproof.Lockyourworkshop.Tools

not used should be kept in a dry place, inaccessible for

children.

• Don’tforcethetool.Itwilldothejobbetterandsaferat

the rate for which it was designed.

• Usetherighttool.Don’tforcethetoolorattachmentto

do a job for which is was not designed.

• Use proper extension cord. Make sure your extension

cord is in good condition. When using an extension cord,

be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a

drop in voltage resulting in loss of power and overheat-

ing.

• Wearproperclothing.Donotwearlooseclothing,gloves,

neckties, rings, bracelets, or other jewelry which may

get caught in moving parts. Nonslip shoesare recom-

mended. Wear protective hair covering to contain long

hair.Rollyoursleevesuptoabovetheelbows.

• Protectyoureyesbysafetygoggles.Everydayeyeglasses

offer only little protection. They are no safety glasses.

Wear a face or dust mask when working in a dusty envi-

ronment.

• Securework.Useclampsoravicetoholdwork,when

practical. It is safer than using your hand, and it frees

both hands to operate the tool.

• Don’toverreach.Keepproperfootingandbalanceatall

times.

• Maintaintoolswithcare.Keeptoolssharpandcleanfor

best and safest performance. Follow the instructions for

lubricating, and changing accessories.

• Always disconnect the machine before servicing, and

when changing accessories, such as blades, bits, cut-

ters, and the like.

• Onlyuserecommendedaccessories.Consulttheoperat-

ing instructions for the recommended accessories. The

use of improper accessories may cause risk of injury to

persons.

• Neverstandonthemachine.Seriousinjurycouldoccur

if the machine is tipped or if the cutting tool is uninten-

tionally contacted.

• Checkfordamagedparts.Beforefurtheruseofthetool,

a guard or other part that is damaged should be carefully

checked to determine that it will operate properly and

perform its intended function. Check for alignment or

binding of moving parts, breakage of parts, mounting,

and any other conditions that may affect its operation. A

guard or other part that is damaged should be properly

repaired or replaced.

• Directionofwork.Pushtheworkpiecetowardsthesaw-

blade or cutter only in the moving direction of the tool.

• Neverleavethemachineunattendedwhileitisrunning.

Wait until the tool has come to an absolute standstill,

before you leave the machine.

• Usethecorrectpowerconnection.Donotpullthepower

plugtostopthemachineduringwork.Neverremovethe

plug from the socket by pulling the extension cord.

• Alwaysstayattentivetowhatyouaredoing,evenwhen

usingthemachineregularly.Bearinmindthatafraction

of a second is sufﬁcient to cause an injury.

• Keep your safety in mind. Safety is a combination of

common sense and staying alert as long as the machine

is switched on.

Additional safety rules for the belt and disc sanding machine

• WARNING: Do not use your machine until it is completely

assembled and installed according to the instructions.

• Ifyouarenotfamiliarwiththeoperationofthesanding

machine, ask the head of the department, your teacher,

or any other qualiﬁed person.

• ATTENTION: This machine has only been designed for

sanding wood or similar materials. The sanding of other

materials can cause ﬁre, injuries, or damage the prod-

uct.

• Alwayswearsafetygoggles.

• Thismachinemayonlybeoperatedindoors.

• IMPORTANT: Mount and use the machine on a horizontal

surface. A non-horizontal surface can damage the mo-

tor.

• If the machine tends to tilt or walk (especially when

sanding long and heavy panels), it must be fastened to a

solid surface of sufﬁcient carrying force.

• Makesurethesandingbeltrunsinthecorrectdirection

– see arrows at the back of the belt.

• Makesurethesandingbeltisrunningcorrectlysothatit

cannot come off the drive pulleys.

• Makesurethesandingbeltisnottwistedorloose.

• Firmlyholdtheworkpiecewhensanding.

• Alwaysusethefencewhenusingthesandingmachine

in horizontal position.

• Alwaysholdtheworkpiecermlytothetablewhenusing

the sanding disc.

• Always hold the workpiece to the side of the sanding

disc running downwards, in order to maintain the work-

piecepressedtothetable.Byusingtheupwardrunning

side of the sanding disc, the workpiece could be ejected

and cause injury to persons.

• Alwayskeepaminimumdistanceof about1.5mmor

less between the table or fence and the sanding belt or

disc.

• Donot weargloves.Do nothold the workpiecewith a

cloth during sanding.

• Usesandingbeltordiscofthecorrectgritcorresponding

with the wood.

• Neversandworkpiecestoosmalltobeheldsafely.

• Avoidawkwardhandpositionswhereasuddenslipcould

cause your hand to touch the sanding belt or disc.

• Whensandingalargepieceofmaterial,provideanad-

ditional support at table height.

• Neversandanunsupportedworkpiece.Securethework-

piece with the table or the fence. Exceptions are the

sanding of curved workpieces on the outside of the sand-

ing disc.

• Alwaysclearthetable,fenceorsandingbeltofscrapsor

other objects, before turning the machine on.

• Donotperformanylayoutassemblyorsetupworkon

the table while the sanding machine is in operation.

• Switchthemachineoffandpullthepowerplugfromthe

socket when ﬁtting or removing accessories.

• Never leave the working area of the sanding machine

while the tool is running, or as long as it has not come to

an absolute standstill.

m Proper Use

The machine meets the currently valid EU machine directive.

• Themanufacturer’s safety, operation and maintenance

instructions as well as the technical data given in the

calibrations and dimensions must be adhered to.

• Relevantaccidentpreventionregulationsandothergen-

erally recognized safety and technical rules must also be

adhered to.

• Themachinemayonlybeused,maintainedorrepaired

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach BD9000 in the language / languages: English, German as an attachment in your email.

The manual is 0,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach BD9000 Manual

Product: