Manual Scheppach Basa 5.0 (page 26 of 148) (All languages)

781468

Zoom out

Zoom in

1/148

Montage

The machine is not completely assembled

for reasons of transport.

Assembly tools:

13 mm fork wrench

5 mm hexagonal socket wrench

(not included in delivery)

Guide pipe

Fig.“2“

The fence plate underneath the sawblade

has been tted in the works.

Before attaching the guide tube, check

the fence plate for tight t.

If necessary, tighten the clamping levers (1).

Fit the steel holding devices for the guide tube at

the lett and right-hand side of the fence plate.

2 cheese head srews M8 x 16

2 washers

2 steel holding devices

Push the gu!de lube mto the holding devices from

the side. Before tightening the hexagon boIts,

check the parallelity of the guide tube with the

table (dimension „x“).

Dimension „x“ must be identical at the front

and at the rear of the table.

Fence

Fig. „3“

• The fence can be used to the Ieft or

the right of the saw band depending

on wone requirements.

Screw together the feace pipe, intermediate plate,

and guide slide (handscrewed). To da this, insert

both threaded screws into the guide slots.

4 washer 6

4 cheese head screws M6x20

• The divider plate to carry the fence is

screwed onto the fence pipe on the

right or the Ieft depending on the work

requirements.

Do not tighten the wing nuts!

2 saucer-head screws M 6 x 75

2 washers 6

2 wing nuts M6

Place fence rail onto the divider plate.

Position 1: for work with a higher contact surface

Position 2: for work with a lower contact surface

Place the cam lever on the guide slide horizontally.

Place the guide slide onto the guide pipe and push

the cam lever down - c!amp.

On the guide pipe, the upper scale applies to

position 1; the Iower scale to position 2.

Fence adjustment

Fig.“4“

Place the fence on the guide rail.

Place a straight strip on the sawband running

upwards and downwards.

Place an angle on the strip and on the fence.

Adjusting the reading glass

Fig.“5“

The guide tube must project over the sawblade to

such an extent that the scale on the guide tube is

positioned directly under the zero mark of the

magnifying glass.

Release the two belts of the magnifying glass and

set the graduation mark precisely above the

zero mark of the scale.

Retighten the bolts of the magnifying glass.

Setting before inital operation

The electrical current supply is interrupted by a

limit switch when the housing lid is opened!

Cutting speeds

Fig. „6“

Band saw are quipped with 2 cutting speed.

IMPORTANT!

The cutting speed may only be set while the

machine is at a full stop. Pull the mains plug!

Two levels

460 m/min. for wood and hardwood

775 m/min. for soft wood

V-belt 10 x 1072 mm

Cutting speed - levels I - II

463 m/min. 1 to 3

775 m/min. 2 to 4

The machine is delivered with apre-set

cutting speed of 775 m/min for wood and hard-

wood

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Basa 5.0 in the language / languages: All languages as an attachment in your email.

The manual is 4.84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Basa 5.0 Manual

Product: