Manual Scheppach Basa 5.0 (page 23 of 148) (All languages)

781468

Zoom out

Zoom in

1/148

diverted from their work.

• The working space on the machine must be free

of chips and wood scrap.

• Wear only close-tting clothes. Remove rings,

bracelets and other jewelry.

• Always wear safety goggles when working.

• Wear a cap or hair net to protect long hair.

• Wear suitable gloves to change the sawband.

• Do not wear work gloves when working on the

saw.

• Observe the correct rotational speed setting on

the machine.

• The safety mechanism on the machine may not

be removed or rendered unusable.

• Cleaning, changing, calibrating, and setting of

the machine may only be carried out when the

motor is switched off. Pull the power supply plug

and wait for the rotating tool to completely stop.

• Connection and repair work on the electrical

installation may be carried out by a qualied

electrican only.

• All protection and safety devices must be repla-

ced after completing repair and maintenance

procedures.

• Switch the machine off and pull power supply

plug when rectifying any malfunctions.

• Use a suction unit to suck up wood shavings

and sawdust. The current speed at the suction

connection piece should be 20 m/s.

• Check the saw band guide and the saw band

tension before starting up.

• Do not use nicked saw bands or those that have

an altered form.

• Replace table inserts that have worn saw slots.

• When sawing round wood, make sure that the

work piece does not turn.

• For sawing heavy or cumbersome pieces, use

the appropriate working aids for bracing.

(Special accessory roller stands).

• Place the upper saw band guide as closely as

possible to the work piece.

• On slanted table plates, attach the longitudinal

stop on the lower table plate half.

• Do not brake the saw band with side pressure

after switching off.

• Remove work pieces that have become stuck

only with the motor switched off and with the saw

band at a standstill.

• Cut off the external power supply of the ma-

chine even if only minor changes of place are

envisaged. Properly reconnect the machine to

the supply mains before recommissioning.

• When leaving the work place, switch the motor

off. Pull the power supply plug.

 Use only as authorized

 CE tested machines meet all valid EC

machine guidelines as well as all relevant

guidelines for each machine.

• All protective and safety device must be moun-

ted on the machine before beginning work.

• The machine is designed to be operated by one

person. The operator is responsible for all other

persons in the working area.

• Observe all safety instructions and warnings

attached to the machine.

• See to it that safety instructions and warnings

attached to the machine are always complete

and perfectly legible.

• The bandsaw with the supplied tools and acces-

sories is designed exclusively for sawing wood,

material similar to wood, and non- ferrous metals

and steel.

• The maximum dimensions for workpieces to be

processed is may not exceed the bench size in

the standard version. Clearance width: 440 mm,

Clearance height: 300 mm

• For larger workpiece dimensions which require

tipping of the table top, the table extension or

the dolly (special accessories) must be used.

• The band saw can also be used for sawing me-

tal when it is equipped with a special saw band

dolly (special accessory) and a operated at an

adapted cutting speed. Metal allows with more

than 80 % magnesium may not be processed

due to the danger of res.

• When used in enclosed rooms, the machine

must be connected to a vacuum exhaust unit.

Use the dust extractor to remove matchwood or

saw dust. The vacuum support ow rate must be

20 m/s. Subatmospheric pressure 860 Pa.

• The automatic switching unit is available as a

special accessory.

Type ALV 2 Art. No. 7910 4010 230 V/50 Hz

Type ALV 10 Art. No. 7910 4020 400 V/230

V/50 Hz

• The vacuum exhaust unit automatically switches

on after a 2-3 second delay after the machine

tool is turned on. This avoids overloading the

circuit fuse.

• After turning off the machine tool, the vacuum

exhaust unit remains on for an additional 2-3

seconds and is then automatically switched off.

Remaining dust is thereby removed by vacuum

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Basa 5.0 in the language / languages: All languages as an attachment in your email.

The manual is 4.84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Basa 5.0 Manual

Product: