Manual Scheppach AB1500MAX (page 15 of 48) (English, German, French, Polish)

781883

Zoom out

Zoom in

1/48

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

15 І 48

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

Starting the equipment

Using the chisel Fig. 2

• Clean the tool before tting it and apply a thin coating

of grease to the tool shaft.

• Pull back the SDS MAX chuck lock (4) as far as pos-

sible. Insert the chisel as far as possible and turn it

until it locks.

• Release the SDS MAX chuck lock. It should only be

possible to move the chisel in the drill chuck by ap-

proximately 1 cm forwards or backwards.

• Check the lock by pulling the tool.

Removing the tool

To remove the tool, proceed in reverse order.

Turn the tool Fig. 3

To turn the tool into the correct position, the rear

unlocking ring (a) must be pulled and held. After this

the tool can be rotated to the desired position. To x the

position release the release ring (a) and insure that it is

reliably locked.

Additional handle Fig. 2

For safety reasons you must only use the demolition

hammer with the additional handle.

The additional handle (3) enables you to achieve better

stability whilst using the demolition hammer.

For safety reasons the machine must not be used with-

out the additional handle (3).

The additional handle can be turned into any required

position. Undo the lock of the additional handle (3) by

turning the handle (3) counterclockwise. Then turn the

handle (3) into the most comfortable working position

and tighten the handle (3) by turning it clockwise.

Operation / Work instructions

Caution! For your safety, the machine must be held

only at the two handles (1 and 3, Figure 1)!

This will avoid the danger of an electric shock through

contact of lines during chiselling.

Switching on / off (Fig. 4)

This power tool works with torque switching.

Warning! Hold power tool safely on the main and ad-

ditional handle! Press until the power button! Otherwise

there is a risk of injury!

Hold power tool safely in vertical position on the main

and additional handle.

To switch on: Press the control switch (2).

To switch off: Release the control switch (2).

• For continuous operation, press the on/off switch (2)

and the locking button (b) on the handle at the same

time.

• To switch off continuous operation, press the on/off

switch (2) and then release it again.

Always keep the chiselling tools sharp.

Note:

–Work only at low pressure when chiselling

–Excessive pressure loads the motor unnecessarily.

–Sharpen the chisels in time and replace, if necessary.

Replacing the power cable

If the power cable for this equipment is damaged, it

must be replaced by the manufacturer or its aftersales

service or similarly trained personnel to avoid danger.

Cleaning and maintenance

Always pull out the mains power plug before starting

any cleaning work.

Cleaning

• Keep all safety devices, air vents and the motor hous-

ing free of dirt and dust as far as possible. Wipe the

equipment with a clean cloth or blow it with com-

pressed air at low pressure.

• We recommend that you clean the device immediately

each time you have nished using it.

• Clean the equipment regularly with a moist cloth and

some soft soap. Do not use cleaning agents or sol-

vents; these could attack the plastic parts of the equip-

ment. Ensure that no water can seep into the device.

Carbon brushes

In case of excessive sparking, have the carbon brushes

checked only by a qualied electrician. Important! The

carbon brushes should not be replaced by anyone but

a qualied electrician.

Maintenance

There are no parts inside the equipment which require

additional maintenance.

Disposal and recycling

The unit is supplied in packaging to prevent its being

damaged in transit. This packaging is raw material and

can therefore be reused or can be returned to the raw

material system.

The unit and its accessories are made of various types

of material, such as metal and plastic. Defective com-

ponents must be disposed of as special waste. Ask your

dealer or your local council.

Storage

Store the equipment and accessories out of children’s

reach in a dark and dry place at above freezing tempera-

ture. The ideal storage temperature is between 5 and

30 °C. Store the electric tool in its original packaging.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach AB1500MAX in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 3.53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach AB1500MAX Manual

Product: