627790
28
Zoom out
Zoom in
Previous page
1/36
Next page
28
Wartung
Anlage überprüfen
Wasserseitige Dichtheit kontrollieren.
Wasserstand kontrollieren - bei Bedarf nachfüllen
und Anlage entlüften - Mindestüberdruck 1,0 bar.
Kessel-Sicherheitsventil und Abblaseleitung kontrol-
lieren.
Abgasleitung auf freien Querschnitt überprüfen - Re-
visionsöffnungen wieder dicht verschließen.
Abgasleitung auf Dichtheit prüfen.
Funktionsprüfung
Brennwertkessel in Betrieb nehmen.
Gasleitung vom Gasabsperrhahn bis einschließlich
Gasarmatur auf innere und äußere Dichtheit prüfen -
mit antikorrosivem Lecksuchspray absprühen - nicht
auf elektrische Leitungen sprühen.
Maximal zulässiger Prüfdruck der Gasarmatur
150 mbar.
Bei Feststellung von unzulässigen Undichtheiten Gas-
armatur und/oder Gasleitung auswechseln und auf
Dichtheit prüfen.
Brennereinstellung kontrollieren.
Abgasmessung durchführen und protokollieren.
Alle elektrischen Verbindungen überprüfen.
Alle Fühler auf richtigen Sitz überprüfen.
Ionisation messen (Fig. 37):
- Meßgerät auf Gleichspannung stellen (DCV)
- Meßbereich 0-20 V wählen
- Minuspol des Meßgerätes am Meßkontakt 1 anle-
gen, Pluspol des Meßgerätes an die Metallkonsole 2
(Masse) halten.
1 V entspricht 1µA
Sollwert bei minimaler Kesselleistung : > 4 µA
Sollwert bei maximaler Kesselleistung : > 6 µA
Alle Regel- und Sicherheitseinrichtungen auf Funktion
prüfen.
Kesselumwälzpumpe auf Funktion prüfen.
Wasserweiche auf Funktion prüfen.
Wartungsprotokoll ausfüllen - Wartung durch Unter-
schrift bestätigen.
Fronthaube montieren - auf unbeschädigte Dichtung
achten.
Einstellung und Funktion der witterungsgeführten Re-
gelung nach deren Anleitung überprüfen.
Displayanzeigen beim Brennerstartvorgang kontrol-
lieren (siehe rechts).
Heizkörperventile bzw. Mischer in Ausgangsstellung
bringen.
Funktionen beim Startvorgang
(Wärmeanforderung vorhanden)
Standby-Modus
Überprüfung des Verbrennungsluftgebläses
Vorbelüftung
Zündung
............................................................................
wenn innerhalb von 5 Sekunden kein Ionisationssig-
nal vorhanden ist:
Gebläsebetrieb
Zündung
Gebläse wird weggeschaltet
Überprüfung des Verbrennungsluftgebläses
Vorbelüftung
Zündung, wenn kein Ionisationssignal anliegt,
Störmeldung 2 blinkend.
............................................................................
Heizbetrieb - Ionisationssignal vorhanden, oder
Brauchwasserbetrieb - Ionisationssignal vorhan-
den
Fig. 37: Meßanordnung Ionisationsstrom
bis zu 5 mal
0280020
Voltmeter
+ -
1
2
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Schafer Heiztechnik Domo Eco at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Schafer Heiztechnik Domo Eco in the language / languages: German as an attachment in your email.

The manual is 6,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Schafer Heiztechnik Domo Eco

Schafer Heiztechnik Domo Eco User Manual - German - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info