745590

Scan 5004 S FRL Manual

30
Zoom out
Zoom in
Previous page
1/40
Next page
30
The various woods have different calorific values. In other words,
for certain species of wood, you will need to use a greater quantity
to achieve the same heating performance. This Instuction Manual
assumes that you will be using beach, which has a very high calori-
fic value and is also the easiest wood to get hold on.
If you use oak or beech as fuel, you need to bear in mind that
these wood types have a greater calorific value than for example
birch. To avoid any risk of damage to the stove, you should there-
fore make sure to use less fuel in these cases.
CALORIFIC VALUE OF THE WOOD
Wood types kg Drywood/m
3
Compared to beech
Hornbeam 640 110%
Beech/Oak 580 100%
Ash 570 98%
Maple 540 93%
Birch 510 88%
Pine 480 83%
Fir 390 67%
Poplar 380 65%
HANDLING OF THE FUEL
SELECTING WOOD/FUEL
You can use any type of wood as fuel. However harder woods, such as beech or ash, are generally better for heating, as they burn
more evenly and create less ash. Other woods, such as maple, birch and spruce, are excellent alternatives.
PREPARATION
The best fuel is obtained where the tree has been felled and the wood sawn and split before May 1st. Remember to cut the wood
to match the size of the combustion chamber. We recommend a diameter of 6-10 cm. The length should be about 6 cm shorter
than that of the combustion chamber to leave enough space for air to circulate. If the diameter of the wood is greater than the
above, it should be split down its length. Wood that has been split dries faster.
STORING
You need to store the sawn and split wood in a dry place for 1-2 years before it will be dry enough to burn. Wood dries faster if
you stack it in an airy place. Before using it, it is a good idea to store the wood for a few days at room temperature. Remember
that wood absorbs moisture from the air during autumn and winter.
MOISTURE
To avoid problematic impact on the environment and to ensure optimum operating economy, the wood should be perfectly dry
before it can be used as fuel. If you use wood that is too damp, most of the heat it produces will be used up in evaporating the
water. The stove will accordingly not increase in temperature, nor emit heat to the room as a result. This is obviously poor econ-
omy, and it will cause soot build-up on the glass pane, in the stove and in the chimney. Operation using moist wood also pollutes
the environment.
¬ Maximum wood moisture content should not exceed 20%. A moisture content of 15-18% will deliver best efficiency.
¬ An easy way of checking wood moisture content is to knock the ends of the two pieces of wood together. If the wood is moist,
the sound will be slightly muffled.
USE OF THE FOLLOWING AS FUEL IS ILLEGAL
NOTE: It is absolutely prohibited to fire with painted, pressure impregnated or glued wood, or sea driftwood.
NOTE: Nor should you ever burn chipboard, plastics, or treated paper. These contain substances that are hazardous to human
health, to the environment, your stove, and your chimney.
In short - make sure you only use proper wood.
Max load
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scan 5004 S FRL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scan 5004 S FRL in the language / languages: English as an attachment in your email.

The manual is 10,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scan 5004 S FRL

Scan 5004 S FRL User Manual - German - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info