Manual Scan 5003 S FL (page 28 of 36) (English)

745588

Zoom out

Zoom in

1/36

CONTINUOUS OPERATION

It is important to obtain as high a temperature as possible in the combustion chamber. This results in best possible use of the

stove and fuel, as well as achieving clean combustion. In this way you will avoid build-up of soot on the combustion chamber

lining and glass pane. During operation, you should not see any smoke; just a movement in the air that indicates combustion is in

progress.

¬ After completing the lighting phase, you should have a good layer of embers in the stove; you can then start operation of it

properly

¬ Add 3-4 pieces of wood at a time: they should be about 0,5 kg in weight and about 30 cm long

NOTE: The wood must catch ﬁre quickly. This is why we recommend setting the combustion air ﬂow fully open. Operating the

stove at too low a temperature and with too little the combustion air can lead to gases igniting, which can damage the stove.

¬ When adding wood, always open the glass door carefully to prevent smoke escaping

¬ Never add wood, while the fire is burning nicely

WARNING ABOUT OVER-FIRING

If the stove is continiously ﬁred with larger amounts of wood than recommended and/or receives too much air, this can cause

a heavy heat development liable to damage both stove and the surrounding walls. We therefore recommend that you always

observe the max. recommended amount of fuel (See under ”Technical Data”).

FIRING IN THE SPRING OR AUTUMN

In the spring/autumn transition period, where there is less need for heating, we recommend you light the stove “top down” once,

perhaps adding just two pieces of wood to ensure that the combustion chamber lining burns clean again.

GENERAL NOTES

PLEASE NOTE! Parts of the wood-burning stove, especially the outer surfaces, become hot during use. Due care should be

exercised.

¬ Never empty ashes into a ﬂammable container. Ashes can contain glowing embers long after you ﬁnish operating the stove.

¬ When the stove is not in use you can close the dampers to avoid a draught through the stove.

¬ If the stove has not been used for some time, you should check the ﬂue passageways for potential blockages before relighting.

NOTE: Never place ﬂammable material in the radiation zone of the stove!

THE FUNCTION OF THE CHIMNEY

The chimney is the wood-burning stove’s motor; its performance determines how well your stove will work. The draught in the

chimney creates negative pressure in the wood-burning stove. The negative pressure draws the smoke out of the stove and takes

in air through the combustion air damper to fuel the combustion process. Combustion air is also used for the airwash system

that keeps the glass clear of soot.

The draught in the chimney is created by the difference in temperature inside and outside the chimney. The higher the differ-

ence in temperature, the better the draught. This is why it is important that the chimney reaches operating temperature before

you reduce the damper settings to restrict combustion in the stove (a brickwork chimney will take longer to reach operating

temperature than a steel chimney). It is very important that the operating temperature is reached as quickly as possible on days

when the draught in the chimney is poor due to unfavourable wind and weather conditions.

You need to get a few ﬂames going as quickly as possible. Chop the wood extra thin; use an extra ﬁre lighter etc.

¬ After longer periods without use, you must check the chimney ﬂue for blockages.

¬ You can connect several units to the same chimney. You should however ﬁrst check the relevant regulations in this respect.

CHIMNEY FIRE

In the event of a chimney ﬁre, keep the stove door, ash drawer, and all dampers on the stove closed. In an emergency, call the ﬁre

service.

¬ We recommend that you get a chimney sweep to check the chimney before using the stove again.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scan 5003 S FL in the language / languages: English as an attachment in your email.

The manual is 9,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scan 5003 S FL

Scan 5003 S FL User Manual - German - 36 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scan 5003 S FL Manual

Product: