745565

Scan 41 Manual

19
Zoom out
Zoom in
Previous page
1/28
Next page
19
CONTINUOUS OPERATION
It is important to obtain as high a temperature as possible in the combustion chamber. This results in best possible use of the
stove and fuel, as well as achieving clean combustion. In this way you will avoid build-up of soot on the combustion chamber
lining and glass pane. During operation, you should not see any smoke; just a movement in the air that indicates combustion is in
progress.
¬ After completing the lighting phase, you should have a good layer of embers in the stove; you can then start operation of it
properly
¬ Add two pieces of wood at a time: they should be about 0,4-0,6 kg in weight and about 20 cm long
NOTE: The wood must catch fire quickly. This is why we recommend setting the primary air flow fully open. Operating the stove
at too low a temperature and with too little primary air can lead to gases igniting, which can damage the stove.
¬ When adding wood, always open the glass door carefully to prevent smoke escaping
¬ Never add wood, while the fire is burning nicely
WARNING ABOUT OVER-FIRING
If the stove is continiously fired with larger amounts of wood than recommended and/or receives too much air, this can cause a
heavy heat development liable to damage both stove and the surrounding walls. We therefore recommend that you always ob-
serve the max. recommended amount of fuel (See under ”Technical Data”).
USING YOUR STOVE IN VARIOUS WEATHER CONDITIONS
The way the wind affects the chimney can have a big impact on how your stove reacts under various wind loads; you may need to
adjust the airflow to achieve good combustion. Fitting a damper in the flue pipe may also help, as it will allow you to regulate the
draught under changing wind loads. The damper must not close more than 80% of the surface.
Fog and mist can also have a big impact on chimney draught; you may need to use other settings for the combustion air to
achieve good combustion.
FIRING IN THE SPRING OR AUTUMN
In the spring/autumn transition period, where there is less need for heating, we recommend you light the stove “top down” once,
perhaps adding just two pieces of wood as above to ensure that the combustion chamber lining burns clean again.
THE FUNCTION OF THE CHIMNEY
The chimney is the wood-burning stove’s motor; its performance determines how well your stove will work. The draught in the
chimney creates negative pressure in the wood-burning stove. The negative pressure draws the smoke out of the stove and takes
in air through the combustion air damper to fuel the combustion process. Combustion air is also used for the air wash system
that keeps the window clear of soot.
The draught in the chimney is created by the difference in temperature inside and outside the chimney. The higher temperature
difference, the better draught. This is why it is important that the chimney reaches operating temperature before you reduce the
damper settings to restrict combustion in the stove (a brickwork chimney will take longer to reach operating temperature than a
steel chimney). It is very important that the operating temperature is reached as quickly as possible on days when the draught in
the chimney is poor due to unfavorable wind and weather conditions. You need to get a few flames going as quickly as possible.
Chop the wood extra thin; use an extra fire lighter etc.
¬ After longer periods without use, you must check the chimney flue for blockages
¬ You can connect several units to the same chimney. You should however first check the relevant regulations in this respect
CHIMNEY FIRE
In the event of a chimney fire, keep the stove door, the ash container, and all dampers on the stove closed. In an emergency, call
the fire service.
¬ We recommend that you get a chimney sweep to check the chimney before using the stove again
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scan 41 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scan 41 in the language / languages: English as an attachment in your email.

The manual is 3,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scan 41

Scan 41 User Manual - German - 28 pages

Scan 41 User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info