745593
31
Zoom out
Zoom in
Previous page
1/44
Next page
A
NAVN:
STI:
DIMENSION:
MATERIALE:
DATO:
SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg
©
TG.NR:EMNE:
C:\Working Folder\Designs\Scan 1003\91003002.idw
91003002
Tertiærkasse, luftindikator
12-10-2018
BC
Scan 1003
VÆGT:
AREAL:
N/A
N/A
0%-100%0%-100%
B
NAVN:
STI:
DIMENSION:
MATERIALE:
DATO:
SIGN:
Krog Iversen & Co A/S
DK-5492 Vissenbjerg
©
TG.NR:EMNE:
C:\Working Folder\Designs\Scan 1005\91005014.idw
91005014
Tertiærkasse, luftindikator
19-03-2018
KEN
Scan 1005
VÆGT:
AREAL:
N/A
N/A
31
INSTRUCTIONS FOR USE
CB-TECHNOLOGY (CLEAN BURN)
The stove is equipped with CB technology. In order to ensure optimal combustion of gases released during the combustion
process, air passes through a specially developed system of channels. The heated air is conducted into the combustion chamber
through the holes in the rear lining of the combustion chamber and at the baffle plates. This airflow is controlled by the rate of
combustion and cannot therefore be regulated.
NOTE: The wood must never be placed higher than the tertiary holes at the rear of the burn chamber (This does not apply at a
cold start).
BAFFLE PLATE
The baffle plate is located in the upper part of the combustion chamber. The plate holds back smoke, making sure it stays inside
the combustion chamber for a longer time before escaping through the chimney. This reduces the flue gas temperature as the
gases have more time to dissipate heat to the stove.
The baffle plate must be removed for sweeping; see “Maintenance”. Note that the baffle plate is made of porous, ceramic materi-
al, and is liable to break easily. You should therefore handle it with care.
The baffle plate is subject to wear and tear and not covered by the warranty.
PRIMARY AIR
The primary air regulation mechanism is used for lighting the fire, or to boost the burning process when you put wood on. The
primary air vent can be 0 - 60% open if you use hard wood fuel such as oak and beech. You can close the primary air vent if you
use soft wood such as birch or pine for fuel.
Settings for normal load: 0 - 60%
SECONDARY AIR
Secondary air is pre-heated and fed indirectly to the fire. At the same time, the secondary airflow cleans the glass pane to avoid
soot build-up. If you over-restrict the secondary airflow, soot can build up on the glass pane. The secondary airflow determines
the heat output from your wood stove.
Settings for normal load: 40 - 70%
Adjustment of air supply,
primary and secondary damper
Primary airCB-technique
Primary air Secondary air
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scan 1003 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scan 1003 in the language / languages: English as an attachment in your email.

The manual is 5,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scan 1003

Scan 1003 User Manual - German - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info