441342
12
Zoom out
Zoom in
Previous page
1/12
Next page
pag. 11
Manual SA 235
1. the display shows H1 = 1 point adjustment procedure is selected.
2. now place accurate weights of 1/3 of the maximum weighing range
on the weigh platform. (e.g. for a 3 kg scale: place 1 kg)
3. confirm with key , automatically followed by:
4. the weight adjustment will be executed, the most right display figure
runs down from 5 to 0 .
5. the display shows: H2
6. now place accurate weights of 2/3 of the maximum weighing range
on the weigh platform. (e.g. for a 3 kg scale: place 2 kg)
7. confirm with key , automatically followed by:
8. the weight adjustment will be executed, the most right display figure
runs down from 5 to 0 .
9. the display shows: H3
10. now place accurate weights of 3/3 of the maximum weighing range
on the weigh platform. (e.g. for a 3 kg scale: place 3 kg)
11. confirm with key , automatically followed by:
12. the weight adjustment will be executed, the most right display figure
runs down from 5 to 0 .
13. the scale turns off automatically, remove the weight.
14. the scales switches itself on again in the weighing mode.
After completion of the adjusting procedure it is advised to check the scale reading with accurate weights.
Repeat the adjustment procedure if necessary.
The weigh platform is overloaded, a warning "beep" sounds.
Remove the overload as soon as possible.
Weight reading is gross
negative. Zero setting and taring is not possible.
The scale has been switched on with a load on the platform and has set
zero with this load.
After that the load has been removed and now the weight reading is negative.
Switch the scale off and on again with an empty weigh platform.
The scale refuses a zero setting key command.
The measured weight value is outside the zero range (+ and - 2% of the
weighing capacity of the scale).
Zero setting with the tare key is still possible If necessary switch the
scale off and on again with an empty weigh platform: a new zero setting
will be executed.
It is not possible to switch on the checkweigh- or countfuncion.
If one of these functions already is active, it is not possibly to switch on the
other one. Switch off the active function with key > 2 sec.
Switch the scale off and on again.
WEEGTECHNIEK HOLLAND B.V. Website www.satex.nl Tel +31 36 522 20 30
Patroonsweg 23 Email info@satex.nl Fax +31 36 522 20 60
3892 DA ZEEWOLDE The Netherlands
Errors and reports
3 point adjustment: H1 Recommended for Mi and HRMi weight reading setting
returns
from 5 to 0
returns
from 5 to 0
returns
from 5 to 0
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satex SA 235 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satex SA 235 in the language / languages: English as an attachment in your email.

The manual is 0,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satex SA 235

Satex SA 235 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info