699394
83
Zoom out
Zoom in
Previous page
1/110
Next page
SATEL VERSA Plus 81
system identifier – power supply troubles, zone bypasses, troubles of control panel high-
current outputs, communication bus trouble, programming related events, etc.
The identifier consists of 4 hexadecimal characters (digits or letters from A to F). Entering the
value 0000 means that events assigned to that identifier will not be reported. Using the digit 0
in the identifiers is not recommended.
SIA / TELIM prefix – 2 characters which will precede each of the identifiers in case of the
SIA and TELIM formats. Thus an identifier consisting of 6 characters can be obtained. 2
hexadecimal characters (digits or letters from A to F) can be programmed. Entering 00
means that the prefix will not be added. Using the digit 0 in the prefix is not recommended.
Station 1 options / Station 2 options
SIA – send part. name – if the option is enabled, in the SIA format, the name of partition
where the event took place will also be sent, in addition to the event code.
SIA – send source name – if the option is enabled, in the SIA format, the name of event
source (zone, user, etc.) will also be sent, in addition to the event code.
SIA – confirm each block – if the option is enabled, the control panel will wait for
acknowledgement by the monitoring station of receiving every data block sent in the SIA
format. The option applies to telephone reporting.
SIA – id. conf. required – if the option is enabled, the control panel will wait for
acknowledgement by the monitoring station of receiving the identifier with which the data
were sent. The option applies to telephone reporting.
Longer waiting for initial handshake – if the option is enabled, the control panel will wait
longer for handshake from the monitoring station in case of sending events in the Ademco
Express, Contact ID or SIA format. Enable this option in the event of telephone reporting, if
the monitoring station sends a non-standard initial handshake.
Long kiss-off signal – if the option is enabled, the control panel will accept a long kiss-off
(acknowledgment) signal for receiving events in case of Ademco Express and Contact ID
formats. Enable this option in the event of telephone reporting, if the monitoring station
acknowledges receiving events in a non-standard way (the kiss-off signal is longer than
800 ms).
11.2.3 Test transmissions
The test transmission is sent through all transmission paths which are shown on the
list defining the order in which transmission paths are used (see: “Transmission
priority” p. 82).
The test transmission may be sent:
at a specified time. The test transmission code will be sent regularly at a defined time. The
number of days between transmissions and the time of sending transmission are
programmed. Programming the value 0 for days means that the transmission will be sent
everyday (in the same way, as in case programming the value 1).
in specified time intervals. You can program the time intervals in which test transmissions
are to be sent when the system is disarmed and when the system is armed (number of
days, hours and minutes). The test transmission code will be sent:
– after a predefined period of time has elapsed since the last transmission, irrespective of
whether it was a test transmission, or the code of another event was sent (the NO SYNC.
TO LAST TRANSMISSION
option disabled),
at predefined time intervals (the NO SYNC. TO LAST TRANSMISSION option enabled).
83


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Versa Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Versa Plus in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Versa Plus

Satel Versa Plus User Manual - English - 44 pages

Satel Versa Plus Installation Guide - English - 36 pages

Satel Versa Plus Quick start guide - English - 11 pages

Satel Versa Plus Installation Guide - English - 32 pages

Satel Versa Plus Quick start guide - German - 12 pages

Satel Versa Plus Additional guide - German - 113 pages

Satel Versa Plus User Manual - German - 46 pages

Satel Versa Plus Installation Guide - German - 36 pages

Satel Versa Plus Quick start guide - Dutch - 11 pages

Satel Versa Plus User Manual - Dutch - 46 pages

Satel Versa Plus Additional guide - Dutch - 110 pages

Satel Versa Plus Additional guide - Dutch - 2 pages

Satel Versa Plus Installation Guide - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info