699394
67
Zoom out
Zoom in
Previous page
1/110
Next page
SATEL VERSA Plus 65
The test mode is started/ended during polling, which results in a delay, its duration
depending on the programmed response period. The test mode will be turned off
automatically after 30 minutes of:
– starting the test mode from the DLOADX program (the 30-minute period is running from
the moment of exiting the controller settings),
exiting the service mode in the control panel.
According to requirements of the EN50131 standard, the level of radio signals sent by
wireless devices is reduced during the test mode operation.
For the AMD-103 detector, entering the test mode remotely is not possible.
9.4.2 Parameters and options of ABAX system wireless devices
The wireless keypads constitute a special category of wireless devices for which a
separate group of positions is reserved in the controller. For information on configuring
the wireless keypads, refer to the manuals delivered with respective keypads.
Filter – the number of consecutive response periods, during which communication with the
device failed to be established, for the loss of communication with the device to be
reported. Values from the 0 to 50 range can be entered. Entering the digit 0 will disable
control of the device presence in the system.
In the case of the AMD-103 magnetic contact and ASP-100 siren, the presence check
is performed in a different way than for the other ABAX system devices. If the value
programmed for the FILTER parameter differs from 0, the lack of presence will be
reported if no transmission from the AMD-103 magnetic contact / ASP-100 siren is
received within one hour.
Always active [Active mode] – the option is available for the most of wireless detectors. If
enabled, the detector is permanently switched over to the active mode (see “ABAX
wireless detectors p. 71).
The AMD-103 detector and the wireless detectors assigned to 24-h zones are always
in the active mode, therefore the ALWAYS ACTIVE option does not have to be enabled
for them.
Configuration – some of the wireless devices provide additional parameters and options,
which can be configured by radio (shown in square brackets is information on the zone for
which additional parameters can be programmed, if the device takes up more than 1
zone):
AGD-100 – wireless glass-break detector. Sensitivity is to be programmed.
AMD-100 / AMD-101 – wireless magnetic contact. The active reed switch is to be
selected.
AMD-102 – wireless magnetic contact with input for roller shutter detector. The following is
to be programmed:
active reed switch [first zone],
number of pulses after which alarm will be triggered by the roller shutter input
[second zone]
time during which the specified number of pulses must occur for the roller shutter
input to trigger alarm [second zone].
AOCD-250 – wireless outdoor dual technology curtain detector. The following is to be
programmed:
sensitivity of PIR sensor;
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Versa Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Versa Plus in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Versa Plus

Satel Versa Plus User Manual - English - 44 pages

Satel Versa Plus Installation Guide - English - 36 pages

Satel Versa Plus Quick start guide - English - 11 pages

Satel Versa Plus Installation Guide - English - 32 pages

Satel Versa Plus Quick start guide - German - 12 pages

Satel Versa Plus Additional guide - German - 113 pages

Satel Versa Plus User Manual - German - 46 pages

Satel Versa Plus Installation Guide - German - 36 pages

Satel Versa Plus Quick start guide - Dutch - 11 pages

Satel Versa Plus User Manual - Dutch - 46 pages

Satel Versa Plus Additional guide - Dutch - 110 pages

Satel Versa Plus Additional guide - Dutch - 2 pages

Satel Versa Plus Installation Guide - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info