699394
7
Zoom out
Zoom in
Previous page
1/110
Next page
SATEL VERSA Plus 5
1. Introduction
The VERSA Plus alarm system can be configured by using:
keypad,
computer with DLOADX program installed (locally or remotely).
Local programming (using the keypad or DLOADX program) is possible, if one the following
conditions is met:
PERMANENT ACCESS option is enabled (SERV. ACCESS user function ([code]
0. SERVICE 5. SERV. ACCESS) – see: USER MANUAL) – the option is enabled by default,
access to the control panel has been granted temporarily to the service personnel (ACCESS
TIME
user function ([code] 0. SERVICE 6. ACCESS TIME) – see: USER MANUAL).
As required by the standards, the service access after completion of the installation
has to be limited by the administrators.
The built-in INT-VG voice module can be configured by means of the VG-SOFT program.
2. Configuring the control panel with keypad
The control panel can be programmed using the functions available in the service mode. In
case of the LED keypad, programming is subject to some limitations (e.g. entering names is
impossible). Programming the control panel by use of LED keypad is not recommended
by SATEL.
The service mode is indicated on the keypads by means of the
LED. The LED is lit on
the keypad in which the service function menu is available, while it is blinking on all the other
keypads. The service mode may also be signaled acoustically, after the corresponding option
is enabled. Additional information is provided by the
LED, which is:
blinking during navigation throughout the menu and submenus,
lit when any service function is running.
When in the service mode, the alarm system signals no alarms.
2.1 Starting the service mode
1. Enter the service code (by default: 12345) and press the key.
2. Press in turn
. The service mode will be started.
2.2 Starting the service mode “from pins”
When entering the service mode in the normal way is not possible (the control panel does not
support keypads, does not accept the service code, etc.), you can use the emergency
procedure, so-called, starting “from pins”.
1. Power off the control panel (disconnect AC mains first, and the battery next) and make
sure that the control panel is not connected by USB cable to the computer.
2. Place a jumper across the pins located on the control panel mainboard.
3. Power up the control panel (first connect the battery and then the AC power).
4. Wait a few seconds and remove the jumper from the pins. The control panel will enter the
service mode. The service mode menu will be available on the keypad with the lowest
address (in the case of the wireless keypad, the menu will be displayed after pressing any
key).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Versa Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Versa Plus in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Versa Plus

Satel Versa Plus User Manual - English - 44 pages

Satel Versa Plus Installation Guide - English - 36 pages

Satel Versa Plus Quick start guide - English - 11 pages

Satel Versa Plus Installation Guide - English - 32 pages

Satel Versa Plus Quick start guide - German - 12 pages

Satel Versa Plus Additional guide - German - 113 pages

Satel Versa Plus User Manual - German - 46 pages

Satel Versa Plus Installation Guide - German - 36 pages

Satel Versa Plus Quick start guide - Dutch - 11 pages

Satel Versa Plus User Manual - Dutch - 46 pages

Satel Versa Plus Additional guide - Dutch - 110 pages

Satel Versa Plus Additional guide - Dutch - 2 pages

Satel Versa Plus Installation Guide - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info