699394
25
Zoom out
Zoom in
Previous page
1/36
Next page
SATEL VERSA Plus 23
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection.
5.12.3 Control panel power-up / start-up procedure
1. De-energize the 230 V AC circuit to which the transformer is to be connected.
2. Connect the 230 V AC wires to the terminals of transformer primary winding.
3. Connect the terminals of transformer secondary winding to the control panel AC
terminals. To make the connection, use flexible conductors with a cross-section of 0.5 –
0.75 mm
2
, or rigid conductors with a cross-section of 1 – 2.5 mm
2
.
4. Connect the battery to the dedicated leads (positive terminal to RED lead, negative
terminal to BLACK lead). If the battery has screw-type cable lugs, use adapters delivered
with the control panel (do not cut off the battery cable lugs). The control panel will not
start after connecting the battery alone.
5. Turn on 230 V AC power supply in the circuit to which the transformer is connected.
The control panel will start operating.
The above mentioned power-up sequence (first the battery, then the 230 V AC mains)
will ensure proper operation of the power supply unit and the electronic protection
circuits, thus preventing damage to the alarm system components caused by
installation mistakes, if any.
If it is necessary to de-energize the control panel, turn off the main power supply (AC)
first, and the backup power supply (battery) afterwards. Observe the above described
procedure when reconnecting the power supply.
5.12.4 Emergency procedure of the control panel start-up
If the control panel fails to start properly, keypads are not supported, codes are not accepted
by the control panel etc., despite all connections having been made correctly, follow the steps
below:
1. Turn off the control panel power supply (first disconnect the AC power, and then the
battery) and make sure the control panel is not connected to the computer by a USB
cable.
2. Put a jumper on the pins located on the control panel mainboard (designated
in Fig. 2
– p. 9).
3.
Turn on the control panel power supply (first connect the battery and then the AC power).
4. Wait a few seconds and remove the jumper from the pins. The control panel will enter the
service mode. The service mode menu will be displayed on the keypad with the lowest
address (in the case of a wireless keypad, the menu will be displayed on pressing any
key).
If the SERVICE MODE FROM RESET PINS option is disabled in the control panel then,
depending on the type of keypad in which the lowest address is set:
LCD: the , and (of the second partition) LEDs will be lit, and the
message “Restore factory settings ? 1=Yes” will come up on the display,
LED: the and (of the second partition) LEDs will be lit and the
LED will
be blinking rapidly.
Pressing the key will reset the control panel to its factory settings, but will enable
entering the service mode.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Versa Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Versa Plus in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Versa Plus

Satel Versa Plus User Manual - English - 44 pages

Satel Versa Plus Additional guide - English - 110 pages

Satel Versa Plus Quick start guide - English - 11 pages

Satel Versa Plus Installation Guide - English - 32 pages

Satel Versa Plus Quick start guide - German - 12 pages

Satel Versa Plus Additional guide - German - 113 pages

Satel Versa Plus User Manual - German - 46 pages

Satel Versa Plus Installation Guide - German - 36 pages

Satel Versa Plus Quick start guide - Dutch - 11 pages

Satel Versa Plus User Manual - Dutch - 46 pages

Satel Versa Plus Additional guide - Dutch - 110 pages

Satel Versa Plus Additional guide - Dutch - 2 pages

Satel Versa Plus Installation Guide - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info