699463
2
Zoom out
Zoom in
Previous page
1/4
Next page
2 VERSA-MCU SATEL
3. Installation
Disconnect power before making any electrical connections.
The controller should be installed indoors, in spaces with normal air
humidity. When selecting the installation place, remember that the thick
walls, metal partitions, etc. will reduce the range of the radio signal. It is
recommended that the controller be mounted high above the floor. This
will allow you to get a better range of radio communication and avoid
the risk of the controller being accidentally covered by people moving
around the premises. Mounting the controller near electrical installations
is not advisable, as this may cause malfunction of the device.
1. Open the enclosure of the controller (Fig. 2).
2. Make the opening in the enclosure base for the communication bus
and power cables.
3. Pass the cables through the opening. It is recommended to use
a straight-through unshielded cable. When using the twisted-pair
type of cable, the CLK (clock) and DAT (data) signals must not be
sent through one twisted pair.
4. Using wall plugs (screw anchors) and screws, fasten the enclosure
base to the mounting surface.
5. Connect the CLK, DAT and COM terminals with wires to the
communication bus of VERSA control panel.
6. Connect the power leads to the +12 V and COM terminals. If the
distance to the control panel is less than 300 meters, the controller
can be supplied directly from the control panel. If the distance to the
control panel is higher, the controller must be supplied from another
power source, which is located at a closer distance (a power supply
unit or an expander with power supply).
7. Close the controller enclosure.
8. Turn on the power of the alarm system.
9. Start the identification function in the control panel. The controller
will be identified as two devices: INT-RX (address 7) and
VERSA-MCU (address 8).
3.1 Keyfobs
The data relating to keyfobs are stored in the controller. After a controller containing keyfob
data is connected to the control panel, keyfobs will be automatically assigned to the existing
users.
See the VERSA control panel manuals for information on the functions that can be run with
the keyfobs. After adding a keyfob, the functions provided for by the user schedule will be
automatically assigned to the buttons. The assigned functions may be replaced with other
ones.
The user manual for VERSA control panels describes the procedures for adding and editing
the user by means of the keypad, during which you can add or remove the keyfob and
determine what functions will be available from the keyfob.
Adding a 433 MHz keyfob by means of the DLOADX program
Adding a keyfob is possible in the "Versa – Structure" window, "Hardware" tab, after clicking
on the INT-RX in the list of devices. Before making any changes, click on the "Read" button
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel VERSA-MCU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel VERSA-MCU in the language / languages: English as an attachment in your email.

The manual is 0,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel VERSA-MCU

Satel VERSA-MCU User Manual - German - 4 pages

Satel VERSA-MCU User Manual - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info