629722
28
Zoom out
Zoom in
Previous page
1/36
Next page
26 VERSA IP SATEL
5.14.1 Starting the identification function from keypad
1. Enter the service code (by default 12345) and press the key.
2. Press in turn the keys. The service mode will start.
3. Press in turn the keys. The IDENTIFICATION function will start.
Three short beeps will indicate that identification has been completed and information on
the identified devices will be presented (on the display in the LCD keypad and by means
of LEDs in the LED keypad).
4. Press the key to quit the function.
If the identification is terminated by two long beeps, this means that a wrong address
is set in the device connected to the communication bus (unsuitable for this type of
device or the same in at least two devices). The displayed message (in the LCD
keypad) or the blinking LED corresponding to the device address (in the LED keypad)
will be helpful in diagnosing the problem. Press , set the correct address in the
device, and then restart the IDENTIFICATION function.
5.14.2 Starting the identification function from DLOADX program
1. Click on the button in the main menu. The “VERSA – Structure” window will open.
2. Click on the “Hardware” tab.
3. Click on the “Expanders” branch.
4. Click on the “Identification” button to run the identification function.
5. After the identification is finished, a window will appear with a prompt whether to read the
data. Click “OK”.
5.15 Connecting the computer to the control panel
Using a computer, you can configure the alarm system / voice module (DLOADX program /
VG-SOFT) or update the control panel firmware. The communication is encrypted. The
computer can be connected to the control panel through a USB port. After connecting the
control panel to the computer, the Windows system will automatically detect that a new
device is connected and will install system drivers for the HID interface device.
5.16 Installation of ABAX wireless devices
This section does not cover installation of the wireless keypads. They constitute
a separate category of devices and should be installed according to the manual
delivered with the device.
If an ABAX wireless system controller (ACU-120 / ACU-270 / ACU-100 / ACU-250) is
connected to the control panel, you can proceed to installation of ABAX wireless devices
after control panel start-up and controller identification by the control panel. Before installing
a wireless device, check the level of radio signal received by the device from controller and
by the controller from device at the planned installation place. The ARF-100 tester is a useful
tool to check the signal level. The level of signal received by device/controller may not be
lower than 40%. If the radio signal level at the planned installation place is too low, select
another installation location. Sometimes it is sufficient to move the device ten or twenty
centimeters to obtain a significant improvement of signal quality. You can install the device
permanently only after reaching the optimum level of radio signal.
The wireless devices must be registered to the alarm system. This can be done using the
DLOADX program or LCD keypad.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel Versa IP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel Versa IP in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel Versa IP

Satel Versa IP Quick start guide - English - 11 pages

Satel Versa IP User Manual - English - 32 pages

Satel Versa IP User Manual - English - 43 pages

Satel Versa IP Additional guide - English - 93 pages

Satel Versa IP Quick start guide - German - 11 pages

Satel Versa IP Additional guide - German - 97 pages

Satel Versa IP User Manual - German - 45 pages

Satel Versa IP Installation Guide - German - 38 pages

Satel Versa IP Quick start guide - Dutch - 2 pages

Satel Versa IP User Manual - Dutch - 45 pages

Satel Versa IP Quick start guide - Dutch - 12 pages

Satel Versa IP Additional guide - Dutch - 93 pages

Satel Versa IP User Manual - Dutch - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info