699458
60
Zoom out
Zoom in
Previous page
1/87
Next page
58 VERSA SATEL
ASD-150 – enter 2 digits:
1
st
digit – option to signal alarm from other ASD-150 detectors: 0 (disabled) or 1 (enabled).
2
nd
digit – option to send out alarm to other ASD-150 detectors: 0 (disabled) or 1
(enabled).
AVD-100 – for the magnetic contact, enter the digit 0 (bottom reed switch) or 1 (side reed
switch) to determine which of the two reed switches is to be active. For the vibration
detector, enter 2 digits:
1
st
digit – sensitivity: from 1 to 8 (1 – minimum; 8 – maximum).
2
nd
digit – number of pulses: from 0 to 7. For the value 0, pulses are not counted.
ASP-100 – enter 2 digits:
1
st
digit – type of acoustic signaling: from 1 to 4.
2
nd
digit – maximum duration of signaling: 1 (1 minute), 2 (3 minutes), 3 (6 minutes) or 4 (9
minutes).
ASP-105 – enter 2 digits:
1
st
digit – type of acoustic signaling: from 1 to 4.
2
nd
digit – maximum duration of acoustic signaling: 1 (1 minute), 2 (3 minutes), 3 (6
minutes) or 4 (9 minutes).
ASP-205 – for both positions taken on the list by the siren, enter 3 digits:
1
st
digit – maximum duration of signaling: 1 (1 minute), 2 (3 minutes), 3 (6 minutes) or 4
(9 minutes).
2
nd
digit – type of acoustic signaling: 0 (disabled), 1 (sound type 1), 2 (sound type 2) or 3
(sound type 3).
3
rd
digit – optical signaling: 0 (disabled) or 1 (enabled).
ASW-100 E / ASW-100 F – enter 0 (only remote control of the electric circuit); 1 (remote or
manual control of the electric circuit) or 2 (remote or manual control of the electric circuit,
but with option to manually block the remote control).
LCD keypad
You can configure the operating parameters of wireless device:
immediately after adding the device to the system (for the procedure of adding ABAX
wireless devices, refer to the INSTALLER MANUAL),
using the C
ONFIG.DEVICE function (SERVICE MODE 2. HARDWARE 1. KPDS & EXPS
3. W
IRELESS DEV. 2. CONFIG.DEVICE). Having started the function, use the and
keys to select the zone to which the wireless device is assigned and press .
The programming is performed using the “step by step” method (see: p. 6). Described below
are programming settings for the wireless devices for which additional configurable options
and parameters are available.
AGD-100 detector
1. Enter a number from the 0 to 50 range to define the rules of device presence control, and
then press .
2. Press any numeric key to define whether the detector is to be always active ( – no,
yes), and then press .
3. Enter a digit from the 1 to 3 range to define sensitivity (1 – low, 2 – medium, 3 – high),
and then press
.
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel VERSA 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel VERSA 15 in the language / languages: English as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel VERSA 15

Satel VERSA 15 Quick start guide - English - 11 pages

Satel VERSA 15 Installation Guide - English - 36 pages

Satel VERSA 15 User Manual - English - 32 pages

Satel VERSA 15 User Manual - English - 42 pages

Satel VERSA 15 Additional guide - German - 11 pages

Satel VERSA 15 User Manual - German - 44 pages

Satel VERSA 15 Installation Guide - German - 37 pages

Satel VERSA 15 Quick start guide - German - 2 pages

Satel VERSA 15 Quick start guide - Dutch - 11 pages

Satel VERSA 15 User Manual - Dutch - 44 pages

Satel VERSA 15 Quick start guide - Dutch - 2 pages

Satel VERSA 15 Additional guide - Dutch - 86 pages

Satel VERSA 15 Installation Guide - Dutch - 35 pages

Satel VERSA 15 Quick start guide - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info