699458
30
Zoom out
Zoom in
Previous page
1/87
Next page
28 VERSA SATEL
– in case of arming by means of the LCD keypad, the control panel will check if there are
any zones bypassed in the partition – information on the bypassed zones is presented,
if the user has the INSPECTION right,
the warning alarm feature is enabled in the system (see: WARNING ALARM global option),
the warning alarm is signaled at the 2. INTERNAL SIREN function output (ref. WARNING
ALARM ON INTERNAL SIRENS
global option).
You can enable/disable the option in keypad: SERVICE MODE 2. HARDWARE 1. KPDS &
EXPS
. 4. OPTIONS GRADE2.
Serial data on OUT 3/4 – if the option is enabled, OUT3 and OUT4 outputs send the system
status data (zone alarms, fire alarms, troubles, armed modes, etc.) and do not execute any
other programmed functions. The outputs may be used to control the NR2-DSC radio
monitoring transmitter (NEMROD system – PC-16 OUT format), made by NOKTON.
OUT 3/4 data extended mode – if the option is enabled, the OUT3 and OUT4 outputs will
send the system status data in the form of frames (PC-16 OUT UA format). The option is
available, if the SERIAL DATA ON OUT 3/4 option is enabled.
Arm./Disarm./Clear. signaling from zones only – if the option is enabled, outputs with the
functions 1. EXTERNAL SIREN and 2. INTERNAL SIREN with enabled ARM/DISARM/CLEAR SIGN.
option will signal only:
starting of the arming procedure by zone or by means of keyfob,
– no possibility of arming (see: PREVENT ARMING IF NOT READY option or GRADE 2 option), if
the arming command has been sent from keyfob,
failed attempt of arming by means of keypad or keyfob (see: PREVENT ARMING IF NOT
READY
option or GRADE 2 option),
disarming by zone or by means of keyfob,
alarm clearing by zone or by means of keyfob.
Starting the arming procedure, disarming or alarm clearing by means of keypad, proximity
card arm/disarm device or timer are not signaled.
Clear messaging on alarm clearing – if the option is enabled, clearing the alarm will
automatically cancel messaging about this alarm, if the user clearing the alarm has the
T
EL. MESS. CLEARING right.
Service message after tamper alarm – if the option is enabled, information on the tamper
alarm can only be cleared from the troubles memory by using the service code. In the LCD
keypad, the “System tamper, call service” message will be displayed after the tamper
alarm (unless the alarm messages are displayed). The message will no longer be
displayed after the troubles memory is reset by the service.
Warning alarm – if the option is enabled, the warning alarm feature is enabled. It purpose is
to delay the loud signaling and reporting, if any mistakes are made when entering the
protected facility. The warning alarm is not reported. It can be signaled on the keypad,
proximity card arm/disarm device or outputs with the function 2. I
NTERNAL SIREN. The
warning alarm is triggered by the following zone types:
– 0. ENTRY/EXIT or 1. ENTRY/EXIT FINAL – unless the system is disarmed before completion
of the ENTRY DELAY countdown,
– 2. ENTRY/EXIT ROUTE – if it is violated during the ENTRY DELAY countdown, and the
system is not disarmed before completion of the D
ELAY TIME countdown,
– 3. I
NSTANT – if it is violated during the ENTRY DELAY countdown.
The warning alarm lasts 30 seconds. Unless the alarm system is disarmed during this
time, the alarm will be triggered by the zone.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel VERSA 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel VERSA 15 in the language / languages: English as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel VERSA 15

Satel VERSA 15 Quick start guide - English - 11 pages

Satel VERSA 15 Installation Guide - English - 36 pages

Satel VERSA 15 User Manual - English - 32 pages

Satel VERSA 15 User Manual - English - 42 pages

Satel VERSA 15 Additional guide - German - 11 pages

Satel VERSA 15 User Manual - German - 44 pages

Satel VERSA 15 Installation Guide - German - 37 pages

Satel VERSA 15 Quick start guide - German - 2 pages

Satel VERSA 15 Quick start guide - Dutch - 11 pages

Satel VERSA 15 User Manual - Dutch - 44 pages

Satel VERSA 15 Quick start guide - Dutch - 2 pages

Satel VERSA 15 Additional guide - Dutch - 86 pages

Satel VERSA 15 Installation Guide - Dutch - 35 pages

Satel VERSA 15 Quick start guide - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info