699458
31
Zoom out
Zoom in
Previous page
1/36
Next page
SATEL VERSA 29
5.15 Installation of 433 MHz wireless detectors
If the 433 MHz wireless system controller (VERSA-MCU) is connected to the control panel,
you can proceed to installation of the 433 MHz wireless detectors after control panel start-up
and controller identification by the control panel. Before installation of the detector, register it
in the controller and check, if transmissions from the detector located at the planned
installation place can reach the controller. To send a transmission, you can e.g. open the
detector tamper switch. If transmissions from the detector planned installation place do not
reach the controller, select another location. Sometimes, it is sufficient to move the detector
by some ten to twenty centimeters. Only after making sure that the controller receives
transmissions from the detector, you can install the detector permanently.
The wireless detectors must be registered to the alarm system. This can be done using the
DLOADX program or LCD keypad.
5.15.1 Adding new 433 MHz wireless detectors
The control panel can support up to 30 wireless detectors.
DLOADX program
You can add 433 MHz wireless detectors in the “VERSA – Structure” window, “Hardware”
tab, after clicking on the VERSA-MCU controller name in the list of devices.
1. Click on the “Read” button to read the data related to wireless detectors from the
controller (these data are not read after clicking on the
button in the main menu).
2. Click on the zone to which a new wireless detector is to be assigned (you can also select
the zone later in the “New wireless dev.” window).
3. Click on the “New device” button. The “New wireless dev.” window will open.
4. Enter the 7-digit serial number of the added detector. The serial number can be found on
the electronics board or on the enclosure.
5. Open the detector tamper contact.
6. The message will confirm that a new detector has been added (unless you have entered
an invalid serial number, of which you will be informed by a message). The new zone
name will be displayed. You can change it.
7. Click on the “OK” button (you can click on the “Quit” button to cancel adding a new
detector or on the “Next” button to proceed to adding a next wireless detector).
8. Click on the “Write” button to write the new wireless detector data to the controller (these
data will not be written after clicking on the button in the main menu).
LCD keypad
You can add the 433 MHz wireless detectors in the service mode by means of the NEW
DEVICE
function (SERVICE MODE 2. HARDWARE 1. KPDS. & EXPS. 3. WIRELESS MOD.
1. NEW DEVICE).
1. Having started the function, enter the 7-digit serial number of the added detector and
press the key. The serial number can be found on the electronics board or on the
enclosure.
2. Open the detector tamper contact.
3. Information on the detector to be added will be displayed (if nothing happens, it can mean
that you have entered an invalid serial number – if this is the case, press to return
to the submenu). Press to confirm your intention to add a detector.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel VERSA 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel VERSA 15 in the language / languages: English as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel VERSA 15

Satel VERSA 15 Quick start guide - English - 11 pages

Satel VERSA 15 Additional guide - English - 87 pages

Satel VERSA 15 User Manual - English - 32 pages

Satel VERSA 15 User Manual - English - 42 pages

Satel VERSA 15 Additional guide - German - 11 pages

Satel VERSA 15 User Manual - German - 44 pages

Satel VERSA 15 Installation Guide - German - 37 pages

Satel VERSA 15 Quick start guide - German - 2 pages

Satel VERSA 15 Quick start guide - Dutch - 11 pages

Satel VERSA 15 User Manual - Dutch - 44 pages

Satel VERSA 15 Quick start guide - Dutch - 2 pages

Satel VERSA 15 Additional guide - Dutch - 86 pages

Satel VERSA 15 Installation Guide - Dutch - 35 pages

Satel VERSA 15 Quick start guide - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info