699459
10
Zoom out
Zoom in
Previous page
1/11
Next page
8 VERSA SATEL
The user can have two keyfobs:
433 MHz keyfob – supported by the 433 MHz keyfobs receiver expansion module or 433
MHz wireless system controller,
APT-100 bidirectional keyfob – supported by the ABAX wireless system controller.
A single keyfob enables up to 6 functions to be executed. The list of functions assigned to the
buttons / combination of buttons should be obtained from the person who configured the
keyfob settings when adding / editing a user. In the case of APT-100 keyfob, that person
should also provide information about functionality of the LEDs. The keyfob LEDs can be
used to confirm execution of functions, as well as to indicate the system status (pressing
a button on the APT-100 keyfob is accompanied by the LEDs flashing rapidly three times,
and in a little while the LED(s) may come on for 3 seconds to provide information).
3. Operating the alarm system by telephone
If the INT-VG voice module is connected to the control panel, you can operate the alarm
system by using a touch-tone (DTMF) telephone. The voice menu makes the operation an
easy job. To access the voice menu, call the phone number of the control panel.
3.1 Starting the operating by telephone
1. Call the control panel phone number. After the call is received, you will hear three short
beeps.
The installer can configure the control panel in such a manner that the telephone
communicator will only go off hook after the recall. If this is the case, call the number,
but hang up after the number of rings which has been set by the installer. Call again
within three minutes. The call will be received.
2. Enter the code from the telephone keypad and confirm by pressing #. 4 short beeps
followed by 1 long beep will confirm you have got access to the interactive voice menu. If
your code does not authorize you to get access, you will hear three long beeps in the
headset. If the code is incorrect, you will hear two long beeps in the headset.
3. Messages of the interactive voice menu will be played back. They will inform you which
telephone keys you should use to be able to operate the control panel.
3.2 Ending the operating by telephone
1. Press
*
key.
2. Press in turn the 0# keys. The control panel will go on-hook.
The control panel will goes on hook automatically after one minute of idle state.
4. VERSA CONTROL application – first steps
If the ETHM-1 Plus module is connected to the control panel, you can operate the alarm
system from mobile devices using VERSA CONTROL application. Additionally, the
application can provide information about alarm system events by using push notifications.
You can download the application from the internet stores: “Google play” (Android system
devices) or “App Store” (iOS system devices).
Having installed the application:
enter the name of control panel (to enable identification of the control panel when using
the application),
enter the MAC address of ETHM-1 Plus module,
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel VERSA 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel VERSA 10 in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel VERSA 10

Satel VERSA 10 Additional guide - English - 87 pages

Satel VERSA 10 Installation Guide - English - 36 pages

Satel VERSA 10 User Manual - English - 32 pages

Satel VERSA 10 User Manual - English - 42 pages

Satel VERSA 10 Quick start guide - German - 11 pages

Satel VERSA 10 Additional guide - German - 89 pages

Satel VERSA 10 User Manual - German - 44 pages

Satel VERSA 10 Installation Guide - German - 37 pages

Satel VERSA 10 Quick start guide - German - 2 pages

Satel VERSA 10 Quick start guide - Dutch - 11 pages

Satel VERSA 10 User Manual - Dutch - 44 pages

Satel VERSA 10 Quick start guide - Dutch - 2 pages

Satel VERSA 10 Additional guide - Dutch - 86 pages

Satel VERSA 10 Installation Guide - Dutch - 35 pages

Satel VERSA 10 Quick start guide - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info